Results 1 to 15 of 15

Thread: Turning the Scooter in tight spaces?

Hybrid View

  1. #1
    Registered User
    Join Date
    Sep 2013
    Posts
    14

    Turning the Scooter in tight spaces?

    Hi All
    My driveway is sloped just about all the way up to the garage.
    My garage is limited in width. (it's one of those 1,5 car garages with work table and cupboards either side)
    Turning the scooter around in the garage is a small challenge every time.

    If I try to turn it on the driveway, its difficult, due to the slope.
    I have basically to do several iterations of backwards and forwards in the garage to get it around. (5 point turn, so to speak)
    Having to lift the side stand, also makes this maneovour tricky.

    On previous BMW R Series, I could swing the bike on one leg of the center stand.
    I know this is a well known tactic but not sure if it is Motorrad sanctioned?
    Because of the very rear position of the Scooter center stand, this is just about impossible?
    There is a lot of weight on the front wheel.

    Anyone have any suggestions?
    I am thinking of a very low, 3 wheeled triangular cart, which I can slip under the front wheel, to act as Dolly.
    Then should be able to swing the bike around on the c/stand and front wheel dolly.

    Hopefully though, someone has this problem already figured out?
    I did a quick thread check but could not find the answer.

    Thanks,
    Mike.

  2. #2
    On The Road Again
    Join Date
    Jan 2007
    Location
    California
    Posts
    67

    Lightbulb

    On a polished floor I use a 1/4", 12 x 18' plate, with teflon buttons on the bottom.
    Put scoot center stand on plate, Bob's your uncle.

  3. #3
    IBA #44567 Ken F's Avatar
    Join Date
    Sep 2009
    Location
    SW, MO
    Posts
    1,206
    IBA #44567
    "Two things are infinite: the universe and human stupidity; and I'm not sure about the the universe."
    -Albert Eienstein

  4. #4
    Registered User
    Join Date
    Sep 2013
    Posts
    14
    Quote Originally Posted by Ken F View Post
    Thanks Ken and Omega Man,
    The park N move may well be the easiest solution.
    Have either of you perhaps tried it on the Scooter?
    If not, know anyone who has?
    Positioning the pNm and then lifting the bike onto it.
    The actual platform of the pNm looks quite low, so guessing the extra lift is not unmanageable.

    Mike.

  5. #5
    Outlander Omega Man's Avatar
    Join Date
    Jan 2010
    Location
    Mansfield,MA
    Posts
    6,392
    Hi Mike, welcome to the forum! Take a peek at this site- http://www.legalspeeding.com/Park-n-Move.htm
    There have been threads on this "Park and Move" before and it seems well received.
    Gary
    "Well they say.. time loves a hero but only time will tell.. If he's real, he's a legend from heaven If he ain't he was sent here from hell" Lowell George
    2009 F800GS 1994 TW200
    Part of the Forum Threadside Assistance Program

  6. #6
    Registered User RINTY's Avatar
    Join Date
    Nov 2005
    Location
    Calgary, Alberta
    Posts
    4,305
    Mike:

    I ride mine in and park it parallel to, and ahead of my car. To exit, I get on the bike, walk it out backwards, and do a 90 degree reverse turn onto the garage apron, parallel to the front of the garage, then put it back on the stand. Works good.

    I find that as long as I'm straddling the bike, I can control it.
    Last edited by RINTY; 09-20-2013 at 01:26 PM.
    Rinty

    "When you don't know where you're going, any road will get you there."

  7. #7
    rabid reader dbrick's Avatar
    Join Date
    Apr 2003
    Location
    Santa Cruz CA
    Posts
    1,755
    How long is the driveway? Is it straight? If not too steep, you could just paddlewalk backwards out of the garage and roll down to the street.
    David Brick
    Santa Cruz CA
    2007 R1200R

  8. #8
    Registered User
    Join Date
    Sep 2013
    Posts
    14
    Quote Originally Posted by dbrick View Post
    How long is the driveway? Is it straight? If not too steep, you could just paddlewalk backwards out of the garage and roll down to the street.
    Thanks dbrick,
    I have to negotiate between 2 * parked cars.
    Its tight going forward but relatively easy to do. Just got to be careful.
    Trying to go backwards freewheeling down the hill, I have yet to try!
    Regards,
    Mike.

  9. #9
    Registered User
    Join Date
    Sep 2013
    Posts
    14
    Quote Originally Posted by RINTY View Post
    Mike:

    I ride mine in and park it parallel to, and ahead of my car. To exit, I get on the bike, walk it out backwards, and do a 90 degree reverse turn onto the garage apron, parallel to the front of the garage, then put it back on the stand. Works good.

    I find that as long as I'm straddling the bike, I can control it.
    Hi RINTY,
    Thanks for the suggestion.
    I have a very narrow garage apron before the slope.
    I have already tried that technique and it is do-able but a hassle.
    The easily swiveling of the R-series bikes has spoilt me!

    Mike

  10. #10
    RK Ryder
    Join Date
    Sep 2005
    Location
    London, Ontario
    Posts
    2,044
    The car occupying the left side of our driveway is always parked close to the sidewalk, leaving a decent amount of space in front. When returning home, I ride up the driveway, making a left turn in front of the car on the left. From there I paddle/walk it backwards 90 degrees into the garage, ready to be ridden out for the next trip. The other bike is (whichever one it happens to be) is parked on the lift, and when it exits, I make a 90 degree turn out of the garage in front of the left parked car. From there, I fire it up and ride out. Granted, I do have a sloped, three lane driveway, but not a very steep incline.

    If you wish to pay for shipping, feel free to have my turn table affair that I bought years ago from the Duluth Company. I never had much success with it, but it might work for you if the centre stand is at the back of the scooter. I did not have enough weight to lift the front up and pivot the bike around.
    Paul
    Retired and riding my RTs, the '87 K100 & the '98 R1100 !
    Treasurer of the Forest City Motorrad Club #159
    Knights of the Roundel #333

  11. #11
    Registered User
    Join Date
    Sep 2013
    Posts
    14
    Quote Originally Posted by 30300 View Post
    On a polished floor I use a 1/4", 12 x 18' plate, with teflon buttons on the bottom.
    Put scoot center stand on plate, Bob's your uncle.
    Thanks 30300,
    I will goggle Teflon buttons and see where are they available.
    Approx how many buttons did you use on the 12" * 18" plate. On a 2" centre-to-center spacing?

    You using the plate on a typical cement garage floor? You mentioned polished floor?
    Do you think it would work on an unpolished cement garage floor (smooth finish)

    I do not know if I have lost all my strength, but for the life of me I cannot lift the front wheel when the bike is on its center stand.
    Even standing in front of the wheel and grabbing the wheel rim with both hands.
    So, assuming that once you have the Scooter on the plate, do you just swing the back of the scooter around, with the front wheel acting as the center pivot point?

    Thanks a lot.
    Mike

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •