Results 1 to 9 of 9

Thread: Transmission noisy

Hybrid View

  1. #1
    Registered User OLDRIDER's Avatar
    Join Date
    Mar 2003
    Location
    Kennewick, WA
    Posts
    3

    Transmission noisy

    I have a 1990 R100RT with a transmission that rattles in neutral with the clutch out. The local BMW dealer installed new bearings and seals and shimmed it a second time trying to eliminate the knocking with each firing of the piston, heard after the transmission has warmed from riding. What could this be other than improper shimming? Any ideas?
    OldRider

    "It's always been about Riding"

  2. #2
    James.A
    Guest
    What is your idle speed? That kind of noise went away in my R75/5 when I adopted the practice of setting the idle speed above 1000RPM. There is a clue in your statement;"...knocking with each firing of the piston". What you are hearing is the gear sets slapping each other gently at the moment that a cylinder is about to fire and the momentum of motor revolutions gets interrupted. It's almost as if the motor stops for a nano-second before the cylinder fires. Obviously, this would be more pronounced at lower RPMs.

  3. #3
    Bluenoser
    Join Date
    Mar 2010
    Location
    Lethbridge Alberta
    Posts
    456
    Did they service the clutch rod and related bearing? If its noisy in neutral and then the noise goes away when the clutch is pulled in, I'd check the throw out bearing on the clutch rod at the back of the transmission. Just take it apart have a look & service it.
    1971 R50/5 SWB with R75/6 drivetrain
    2013 DL650

  4. #4
    Administrator 20774's Avatar
    Join Date
    Sep 2005
    Location
    San Antonio, TX
    Posts
    13,186
    Too some degree, most transmissions do that. Once the clutch handle is pulled in, the noise should disappear. Mostly, the better the carb synch, the less the noise.
    Kurt -- Forum Administrator ---> Resources and Links Thread <---
    '78 R100/7 & '69 R69S & '52 R25/2
    mine-ineye-deatheah-pielayah-jooa-kalayus. oolah-minane-hay-meeriah-kal-oyus-algay-a-thaykin', buddy!

  5. #5
    James.A
    Guest
    The most rattly transmission I ever heard was in an R1100RSL that I purchased new in 1994. I am convinced that this is not abnormal. I agree with Kurt that well synced carbs can minimize the effect.

  6. #6
    Registered User 88bmwjeff's Avatar
    Join Date
    Aug 2004
    Location
    Walnut Creek, CA
    Posts
    2,555
    Quote Originally Posted by 20774 View Post
    Too some degree, most transmissions do that. Once the clutch handle is pulled in, the noise should disappear. Mostly, the better the carb synch, the less the noise.
    My 88 R100 RT does that. I was told that that's normal for these bikes. I don't worry about. Granted I have good used tranny on the shelf just in case. However, given Murphy's famous law, that item I probably not need.
    Jeff in W.C.
    1988 R100 RT (the other woman)
    "I got my motorcycle jacket but I'm walking all the time." Joe Strummer

  7. #7
    Registered User toooldtocare's Avatar
    Join Date
    Mar 2008
    Location
    Lake Saint Louis, MO
    Posts
    1,727
    I have several bikes that do that, some of them started right after buying new. Even had a car that did that. Always explained it as the gears bouncing around due to uneven firing.

  8. #8
    Registered User OLDRIDER's Avatar
    Join Date
    Mar 2003
    Location
    Kennewick, WA
    Posts
    3
    Quote Originally Posted by James.A View Post
    What is your idle speed? That kind of noise went away in my R75/5 when I adopted the practice of setting the idle speed above 1000RPM. There is a clue in your statement;"...knocking with each firing of the piston". What you are hearing is the gear sets slapping each other gently at the moment that a cylinder is about to fire and the momentum of motor revolutions gets interrupted. It's almost as if the motor stops for a nano-second before the cylinder fires. Obviously, this would be more pronounced at lower RPMs.
    I will bring up the idle speed and see if that helps. It will make smoother shifting as well.

    I'll make sure the carbs are synched which I now understand could be part of the problem.

    Thanks for your advise.

    Bob
    OldRider

    "It's always been about Riding"

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •