Results 1 to 15 of 19

Thread: R75/5 Restoring Tool Tray?

Hybrid View

  1. #1
    Registered User
    Join Date
    Apr 2012
    Location
    Los Angeles, CA
    Posts
    106

    R75/5 Restoring Tool Tray?

    Anyone have suggestions on restoring a tool tray? I know it seems inconsequential. I've removed the old gasket and cleaned all the old adhesive off of the tray. Its got some scratches/dings/etc on it. Was considering wet sanding at least an initial coat to remove the lighter marks in the tray (and any left over adhesive) and then polishing it up slightly.

    Has anyone do anything to (at the very least) bring the color/darkness back on their tool trays for an r75/5 at all?


    Also there is a slight crack in the front of the tool tray. Was wondering if there was a reasonable way to fix crack so that it is not noticeable (without having to paint/etc)



    Cheers,

    Jonathan

  2. #2
    Administrator 20774's Avatar
    Join Date
    Sep 2005
    Location
    San Antonio, TX
    Posts
    13,003
    My /7 tool tray has never been cleaned in any manner...it hardly sees the light of day. The original rubber cushion around the edge is still in good shape. That is the only thing that would be important to keep water out. A crack needs to be fixed, but I suspect any general glue like a JBWeld product or even Gorilla Glue might do a good job...typically you're just sealing for moisture rather than trying to make structural repair.
    Kurt -- Forum Administrator ---> Resources and Links Thread <---
    '78 R100/7 & '69 R69S & '52 R25/2
    mine-ineye-deatheah-pielayah-jooa-kalayus. oolah-minane-hay-meeriah-kal-oyus-algay-a-thaykin', buddy!

  3. #3
    Registered User
    Join Date
    Feb 2012
    Posts
    5
    You might try ABS cement for the cracks. I got some at my local home improvement store. Pretty cheap and it has seemed to work so far. If you have problems finding ABS cement, let me know.
    As far as the scratches, you could always try wet sanding it with some super fine paper. I see that your probably in a different boat than me. But i just fixed the crack and figured that no one was ever going to see my tool tray. But i get the feeling your after a more concourse winning restoration than i was.

    Good Luck

    Chris Palmer
    1982 R100RS

  4. #4
    Registered User
    Join Date
    Jul 2010
    Location
    Tularosa, NM
    Posts
    666

    Rubber Parts --

    A small hijack, just to round-out the discussion. . .apologies ahead of time.

    For those with a worn out tool-tray "nose" rubber, which I don't think can be bought at any price, this:

    If you use some black RTV silicon, you can tastefully "coat" an otherwise roached-out rubber bit, and prolong its' life. I've used this trick on the very end of an Oilhead rubber footpeg, and have stood on it for over two years (yes, I get out on the edge a lot) and it has held up just fine even with this significant stress. Clean well with acetone (or similar solvent), and this stuff will stick like grim death.

    Also - and I can't believe I disagree with Kurt, here. . .Gorilla Glue isn't as strong as a two-part product. I'm also a woodworker, and saw a magazine test of Gorilla Glue, right AFTER using GG to build a set of kitchen drawers (yikes). GG had it's simian ass kicked by Titebond III. Yes, this was on WOOD joints, but it made me look hard at GG, and I don't use it any more, for anything. Better choices out there.

    GG TAPE is - by far - the best TAPE I've ever used - also saw a test of it against Duct Tape, etc., and it outstripped the competition by a long way.

    Serious hijack: I need a tool tray for a '78 R100RS, with or without rubber, cracked or not.

    Walking Eagle
    Last edited by Walking Eagle; 10-17-2012 at 02:13 PM. Reason: cry for help

  5. #5
    Registered User
    Join Date
    Sep 2007
    Posts
    528

    They are available new!!!

    I took the beat up one from my /7 and patched the big holes with JB weld and afetr a good sanding and smoothing with 600 grit I put Dupli-color DIY liquid bed-liner on the inside and used some VFR spray paint on the outside let it sit and cure for two or three. It looks great and will last another 30 years

  6. #6
    Registered User mysteriousfish's Avatar
    Join Date
    Feb 2011
    Location
    Portland, Oregon
    Posts
    94
    have not tried it on my tool trays, but I did use 303 Aerospace Protectant Spray (I am a kayaker, and use it on rubber drysuit gaskets) on my Krauser Bags, which were getting all dried out and pale looking...sprayed it on and let it sit for 10-15 minutes, then wiped it down...amazing results....they look new now....same for the inner surfaces of my RT fairing....I bet it would really restore that plastic tool tray...

    regarding the cracks...if they are on the edges or corners, ++ on the GG black tape...if on a flat surface, try some 1/8" or 1/16" adhesive-backed closed cell foam sheeting...cut to fit and peel and press to apply........I use the black high density stuff from North Shore Industries in Hood River, OR (http://www.northshoreinc.com/) for all kinds of uses (padded the inside edges of my fairing where my knees contact...much better) now that I think of it, a layer in the bed of the tray would also help cushion the tool roll from rattling, etc...I will try it myself this winter as I catch up on my wrenching....
    michael
    __________
    1991 R100 classic; 1980 R100RT

  7. #7
    advrider.com
    Join Date
    Oct 2005
    Posts
    3,192
    They're still available new for $33.

    Anyone know the trick to getting a new gasket to STAY on the top edge of the tray?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •