Dean Stuckmann - Wisconsin
2008 BMW R1200RT
1982 Honda cx500 Turbo
1983 Honda cx650 Turbo
When I need to slide the whole thing forward to optimize the placement of the wheel in the vice I simply hook a tie down strap to each center stand leg and standing at the front of the lift pull the bike forward an inch or two.
Paul Glaves - "Big Bend", Texas U.S.A
"The greatest challenge to any thinker is stating the problem in a way that will allow a solution." - Bertrand Russell
I was ask to post some pics of the sunken bike lift. Here are a few of before during and after.
Very nice installation 4NBike
"Well they say.. time loves a hero but only time will tell.. If he's real, he's a legend from heaven If he ain't he was sent here from hell" Lowell George
2009 F800GS 1994 TW200
Part of the Forum Threadside Assistance Program
Thank you for sharing these photos. I am so tempted to do the same when I get my lift.
Retired and riding my RTs, the '87 K100 & the '98 R1100 !
Treasurer of the Forest City Motorrad Club #159
Knights of the Roundel #333
Very nice job on the sunken lift
The one draw back beside cost and difficulty to construct is the lift will now lose approximately 6 inches of maximum lift due to it's lower starting position. In my experience I use all the lift my Handy Lift provides and sometimes wish for more.
I do like the easier loading and unloading on the lift with the sunken design.
2013 R1200 GSW
Riding is the art of throwing yourself at the ground and missing
If you are inclined to tackle the job your self the cost is not all that bad, rental for a concrete cutter, lumber to build the form and of course the concrete . An estimate to have mine done by a contractor was 3 days and $800.00.The one draw back beside cost and difficulty to construct is the lift will now lose approximately 6 inches of maximum lift due to its lower starting position. In my experience I use all the lift my Handy Lift provides and sometimes wish for more.
Handy makes a number of lifts that when fully raised reach 35 inches one I think goes to 40". I think the HF lifts limits are 29 inches.
It is a messy labor intensive job, clean up takes as much time as the work itself, at the end of the day it all depends on how bad you want one in this configuration. I have never regretted the decision.
Ah, but then we do not know the "altitude" of the OP... do we? Nice project 4N.The one draw back beside cost and difficulty to construct is the lift will now lose approximately 6 inches of maximum lift due to it's lower starting position.
"It is what you discover, after you know it all, that counts." _ John Wooden
1973 R75/5 - original owner
All things said and done, the Handy lift is really one fine lift. However, for the weekend mechanic and one that enjoys working on the bike, the Harbor Freight models work very well and are much cheaper than the Handy lift. They do the same job. I made wings out of 2x6 framing and put 3/8 plywood over that. I use this set up on each side of the HF stand and it works great. I also use good quality tiedowns and the bike is well supported. Final word from me is that the HF lift does a very good job with no regrets from me. My knees really appreciate the lift.
That bike lift from Italy is fantastic, as well as its' price!
HF is prolly my speed too.
another company not mentioned for a bike jack is J&S jacks
Also a question: Is a table lift the only safe/least damage way to lift an RT? I ask since the RT doesn't have a solid frame and best lift point seem to be where the cat is.
2000 R1100RT opal blue "Millenium Falcon"
2006 Suzuki C50 Boulevard blue/silver w/ DJ drive mod.
How can we get a Harbor Freight lift for under $300 these days?
95 R100Rt, 07 650 GS
"He's gone and nothin gone bring him back"
SABMWRA MOA Club#62's Flat Fixer/ current forum moderator
It's not the breaths you take, but the moments that take your breath away-D.Dillon/G. Strait
Don't know what "Handy Lifts" are going for these days, but they are really quality equipment. 10 or so years ago, I used to travel from KC to Marshaltown Iowa and pick up 13-14 lifts for Letko Cycles. Toured the plant, met the workers and was impressed with the quality. Still have one --and at my age it is so much easier to work on my bikes at eye level than to have to "get on the ground".
They weigh about 350#--I know because we had to unload them.
2012 Triumph Tiger 800
1988 Honda Hawk GT
2009 KLR 685
1981 Honda Trail 110