Page 3 of 3 FirstFirst 1 2 3
Results 31 to 45 of 45

Thread: Stebel Horn Install on a KGT 1300

  1. #31
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    As the trigger wire is black and there is still more wiring do to, I quickly threw on some white heat shrink tubing for identification and noted the end.

    I will shrink the tubing later once the final length is established
    Attached Images Attached Images
    Last edited by Semper_Fi; 02-08-2010 at 03:00 AM.

  2. #32
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725

    Mounting the Relay

    The relay shown with the arrow is not OEM equipment it is the relay for my Centech

    The green highlight is where I am mounting the relay for the horn.

    Tools used are a T30 torx and a 10mm wrench
    Attached Images Attached Images
    Last edited by Semper_Fi; 02-08-2010 at 03:01 AM.

  3. #33
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    Detail of relay mounted.

    Note 1 - the hole where the bolt goes thru is a little small, you will need to run the bolt thru to ensure it fits

    Note 2 - the bolt is intentionally mounted upside down (by me) this is to provide the surface area of the washer on the tab of the relay
    Attached Images Attached Images
    Last edited by Semper_Fi; 02-08-2010 at 03:02 AM.

  4. #34
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    Detail of the nut mounting below the relay
    Attached Images Attached Images

  5. #35
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    Relay connection points
    Attached Images Attached Images

  6. #36
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    I decided to create my own power harness as I did not want to use black as a power wire
    Attached Images Attached Images

  7. #37
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    Connecting the power for the horn from the Centech
    Attached Images Attached Images
    Last edited by Semper_Fi; 02-08-2010 at 03:04 AM.

  8. #38
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    This special connector provided in the kit, connects the grounds of the compressor and the bike (from Centech) together
    Attached Images Attached Images

  9. #39
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    Grounds connected
    Attached Images Attached Images

  10. #40
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    The relay is connected

    Please note at the time the length of the control wire (horn) was known i shrunk the white tubing
    Attached Images Attached Images
    2011 R1200 GSA Smoke Grey Metallic Matt
    2009 G450X White
    IBA #35651
    Rogue Moderator

  11. #41
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    Mount Horn under the ABS controller as shown with the zip ties provided
    Attached Images Attached Images

  12. #42
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    Rear zip tie is a litte tricky to get in - detail provided below
    Attached Images Attached Images

  13. #43
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725

    Completed!!

    All wire harnesses dressed and the product tested.

    It is QUITE LOUD!!
    Attached Images Attached Images
    Last edited by Semper_Fi; 02-08-2010 at 03:05 AM.

  14. #44
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    While helping out a friend do his Stebel install he routed the air horn hose differently from the instructions and it seemed a more natural postion for the hose to follow instead of the instructed one.

    Shown below is the alternate routing.

    Up to you which you want to use.
    Attached Images Attached Images
    Last edited by Semper_Fi; 03-06-2010 at 02:18 PM. Reason: Updated with alternate Hose Routing suggestion

  15. #45
    Honey Badger Semper_Fi's Avatar
    Join Date
    Aug 2008
    Location
    Kingston, NH
    Posts
    5,725
    At this point you can put the plastic back on, kick back and have an adult beverage

    2011 R1200 GSA Smoke Grey Metallic Matt
    2009 G450X White
    IBA #35651
    Rogue Moderator

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •