Search:

Type: Posts; User: 174713; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.11 seconds.

  1. Replies
    10
    Views
    489

    So far I've checked the cable ends (round as...

    So far I've checked the cable ends (round as expected so ok) and lubed the cable, noise still exists. Now on to the arm pivot point, case heating up makes sense since the noise is running temp...
  2. Replies
    10
    Views
    489

    I'll take a look at the cable ends and will lube...

    I'll take a look at the cable ends and will lube the cable again. The cold to hot transition leads me to the clutch, maybe the seal where the lever enters the housing. My biggest concern is something...
  3. Replies
    10
    Views
    489

    Clutch cable noise and rough action

    After installing a new clutch cable 2 months ago my new cable pulls like the cable is dry. I can hear noise from the cable and it does not feel as smooth during operation. It does this after 10-15...
  4. Replies
    4
    Views
    371

    Left and right side difference?

    My r100r had two different lengths with the right side being longer if memory serves me correctly.
  5. Replies
    0
    Views
    195

    Bar Back question

    I'm looking at installing a set of Rox bar backs on my 1992 R100R to obtain a more upright riding position. The more I look at the mounting area, windshield mounting, instruments and dash panel it...
  6. Replies
    13
    Views
    834

    Cruise control options

    I'm looking for the best option for a throttle lock or cruise control unit for my 92 R100R. Excel Throttle doesn't list a unit for my bike, neither does Kaoko. Searching this forum didn't produce...
  7. Lasertec vs. Activ

    I'm going through this decision making process as well for 1992 R100R, here is a good thread from the ADV site:

    http://www.advrider.com/forums/showthread.php?t=949627
  8. Replies
    3
    Views
    417

    I did a visual and continuity check. These fuses...

    I did a visual and continuity check. These fuses are the type with exposed wires and blades, not the bayonet style which are hard to inspect. Cleaning their terminal points is not difficult, a small...
  9. Replies
    3
    Views
    417

    Gremlin found

    I went back to the fuses and started removing them one by one then moved them to the next fuse location. All is good, everything is working. It was a bad connection between the fuse blade and fuse...
  10. Replies
    3
    Views
    417

    Electrical Gremlin

    While doing a short ride today I used my turn signals for about 15 minutes then they stopped working (both sides). My flashers and clock also stopped working. All other electrical items work fine...
  11. Replies
    28
    Views
    1,587

    Good find.

    Congrats Dennis from a fellow PA Airhead owner. I had this one on my watch list as an option if I couldn't find a R100 PD. I know, completely different bikes and uses but you can never have enough...
  12. Replies
    14
    Views
    711

    Plot thickens.

    When I put the new cable through the lever out popped a dried up felt pad. It was in the wrong place, should be under the dust cover to keep it from drying out and from collecting road dirt.
  13. Replies
    14
    Views
    711

    Makes sense, I didn't know that was a lubrication...

    Makes sense, I didn't know that was a lubrication point until now. I looked in Haynes and the owners manual, no mention of this. I now have the new cable which came with a small round felt pad, I...
  14. Replies
    14
    Views
    711

    Thanks for the replies. I tried the Anon book,...

    Thanks for the replies. I tried the Anon book, both guys in my area are out of town but they called back right away. I remembered the vice grip trick and called my to bring them. Worked like a charm....
  15. Replies
    14
    Views
    711

    Emergency towing

    I'm stranded with a broken clutch cable, does the club have an emergency towing number? Just found a cable at Bobs, driving 3 hr to pick it up!
  16. Replies
    28
    Views
    3,008

    Problem Solved!

    After checking the dash bulb, starter connections and ignition switch, I installed a voltmeter and found max charging at 13.6V so I decided to replace the wiring harness Air Race Addict suggested. ...
  17. Replies
    2
    Views
    311

    Brake Fluid Leak

    I just noticed my mater cylinder fluid reservoir was only 1/2 full on my R100R this morning. Looking under the brake lever assembly I saw fluid dripping off the nut securing the brake lever on the...
  18. Replies
    4
    Views
    620

    Alternator Brushes

    As part if troubleshooting my glowing charging system dash light I'm replacing these. Just found out BMW switched suppliers and have an order in for 1k. Problem is they will not be available until...
  19. Replies
    3
    Views
    408

    Thanks for the tips.

    Good points, esp staying on with the key in position 1.
  20. Replies
    3
    Views
    408

    Voltmeter Installation

    I am going to install an aftermarket voltmeter on my 1992 R100R and am looking for input on the installation. Where is the best place to tie the wiring in? At the battery? Alternator? Other...
  21. Thread: Hella Regulator

    by 174713
    Replies
    2
    Views
    373

    Hella Regulator

    Anyone had experience with the Hella regulator? Any connection issues or long term issues with the charging system? Thanks in advance for feedback.

    The bike is a 1992R100R
  22. Replies
    28
    Views
    3,008

    Thanks Bill. I haven't checked the wiring...

    Thanks Bill. I haven't checked the wiring harnesses and will include this check along with previous connection check suggestions (key switch, charging bulb, starter relay, starter cables).
  23. Replies
    28
    Views
    3,008

    Should be BULB connection, not BUILD....

    Should be BULB connection, not BUILD....
  24. Replies
    28
    Views
    3,008

    Good ideas, I haven't checked the wiring to/from...

    Good ideas, I haven't checked the wiring to/from the starter circuit. That and build connections are now on the list!
  25. Replies
    28
    Views
    3,008

    Since I've removed, cleaned and used dielectric...

    Since I've removed, cleaned and used dielectric grease on all connections and replaced the battery and diode board I'm leaning toward the dash light connection. Thanks for all the help.
Results 1 to 25 of 60
Page 1 of 3 1 2 3