Search:

Type: Posts; User: PAS; Keyword(s):

Page 1 of 17 1 2 3 4

Search: Search took 0.07 seconds.

  1. I have an 03 RT and the bike can be a handful at...

    I have an 03 RT and the bike can be a handful at slow speeds especially with the power brakes.
  2. Thread: 1 Ball Bearing

    by PAS
    Replies
    6
    Views
    256

    Can you post a picture of the latch?

    Can you post a picture of the latch?
  3. Replies
    3
    Views
    311

    How old is the output shaft seal if its new is it...

    How old is the output shaft seal if its new is it installed backwards? If its old sounds like it needs replaced.
  4. Replies
    10
    Views
    417

    Is the motor out of the bike and on the bench? ...

    Is the motor out of the bike and on the bench? Maybe a machine shop could handle the job.
  5. Replies
    13
    Views
    971

    McMaster Carr 8219K56 High temp wire....

    McMaster Carr 8219K56 High temp wire.
    http://www.mcmaster.com/#catalog/120/821/=qk7yz9
  6. There is a similar conversation going on in...

    There is a similar conversation going on in another forum. Go over and have a read in the Oilheads section.
    http://bmwsporttouring.com/ubbthreads/ubbthreads.php
  7. The OEM black screws on my 03 can be polished to...

    The OEM black screws on my 03 can be polished to a bright finish.
  8. The panels will fit without elongating the holes...

    The panels will fit without elongating the holes once you get the tank moved into the correct position. Take your time.
  9. The gas tank rear mounting point is elongated. ...

    The gas tank rear mounting point is elongated. Leave it loose and move it until the left side panel fits up, then go for it. You may have to loosen the top section piece also. Been there done...
  10. Thread: hard to cold start

    by PAS
    Replies
    28
    Views
    994

    Another area that is often overlooked is in the...

    Another area that is often overlooked is in the float bowl. The corner well that feeds the enrichener has a small hole at the bottom to allow fuel into that chamber. Make sure it isnt plugged up.
  11. Replies
    15
    Views
    709

    That may be all it takes to work!

    That may be all it takes to work!
  12. Replies
    15
    Views
    709

    You do have the correct springs and center...

    You do have the correct springs and center stand?? Max BMW shows the springs are about 6" long.
  13. Replies
    10
    Views
    415

    As suggested, check out item #2 piston. Some are...

    As suggested, check out item #2 piston. Some are plastic and swell from the heat. It can be lightly sanded to a smaller diameter to fix the problem.
    46508
  14. Replies
    3
    Views
    327

    I would add that to have the bezels match each...

    I would add that to have the bezels match each other you have to stay within the same series of gauges. VDO Vison or Cockpit series.
  15. Replies
    9
    Views
    456

    The front brakes on my 81 R100RT are firm and...

    The front brakes on my 81 R100RT are firm and work fine. It still has the original brake lines plus it has over 166K on it. I agree that it sounds like they need bled again.
  16. Replies
    10
    Views
    415

    I have heard that the new cable fitting is not...

    I have heard that the new cable fitting is not shaped correctly and will cause binding and break. If I recall correctly the fitting has a hex shape to it and must be filed to make it round so it...
  17. Replies
    17
    Views
    470

    Previous owner enlarged my battery tray to fit...

    Previous owner enlarged my battery tray to fit the average garden tractor battery but a few years back I went with the PC-680 and never looked back.
  18. Your lucky. the spring broke on my 81 R100 and...

    Your lucky. the spring broke on my 81 R100 and on a friends 82 R100 the spring broke in small piece's and went thru the engine and bearings. Most guys never look in the cavity to see if the ball...
  19. Replies
    13
    Views
    1,090

    There have been several owners that have...

    There have been several owners that have eliminated the iABS servo system. When mine starts to act up it will be history! I just downloaded the procedure this morning.
    03 R1150RT
  20. If you can make it this far, this is near...

    If you can make it this far, this is near Columbus, they specialize in used BMW parts.
    http://www.re-psycle.com/
  21. Thread: Brass Screw?

    by PAS
    Replies
    33
    Views
    1,344

    Sounds like it runs like mine does.

    Sounds like it runs like mine does.
  22. Thread: Do I really?

    by PAS
    Replies
    31
    Views
    1,654

    plus 1 45967

    plus 1
    45967
  23. Thread: Brass Screw?

    by PAS
    Replies
    33
    Views
    1,344

    How long and how many miles have you put on this...

    How long and how many miles have you put on this bike? Perhaps you need to give it some time and not be in a hurry to "fix things". Your getting some good advice but it seems like your having some...
  24. What year is the bike.

    What year is the bike.
  25. Thread: advise please

    by PAS
    Replies
    16
    Views
    933

    I'm just 25 mi.west of Youngstown

    I'm just 25 mi.west of Youngstown
Results 1 to 25 of 420
Page 1 of 17 1 2 3 4