Search:

Type: Posts; User: Picinisco; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.07 seconds.

  1. As opposed to the grinding of stainless steel and...

    As opposed to the grinding of stainless steel and sweaty old machinists.
  2. Pine Sol and it makes the shop smell nice/

    Pine Sol and it makes the shop smell nice/
  3. Thread: Mikuni carbs

    by Picinisco
    Replies
    16
    Views
    4,681

    Not sure that this answers my question. I want to...

    Not sure that this answers my question. I want to add vacuum ports to my VN32 Mikunis and was interested to see where "Richard" had tapped into to achieve this on his VN26s
  4. Thread: Mikuni carbs

    by Picinisco
    Replies
    16
    Views
    4,681

    Richard, I just came across your pics of the...

    Richard, I just came across your pics of the Mikuni carbs that you added vacuum port to. I need to do the same. Can you show me on more detail where on the carbs you actually tapped into. I know it...
  5. Replies
    2
    Views
    272

    I already torqued it to 75 and held the hub...

    I already torqued it to 75 and held the hub steady by tying it to the wheel through several spokes.

    John
  6. Replies
    2
    Views
    272

    Torque Values On R75/5 Final Drive

    I have asked advice as to the torque setting for the nut on the end of the final drive pinion gear and am getting two different answers. I cannot find it in my Clymer Manual. I know it's there just...
  7. Replies
    11
    Views
    1,161

    Alternative, and a tip that was passed on to me,...

    Alternative, and a tip that was passed on to me, is to clean the contact on the half moon sender board with the eraser on the end of a pencil. Works great and actually helps the sender to read "more...
  8. Replies
    16
    Views
    976

    It would seem from all the discussion that torque...

    It would seem from all the discussion that torque is the factor and vibration is what makes under or even over torqued bolts loosen. And I suppose the bolts could in fact back out one at a time until...
  9. Replies
    10
    Views
    621

    Fiamm Car Horns

    A pair of Fiamm car horns will work plug and play. I have made the swap on my last bike 1995 R1100RS and my now 2004 R1150GS. If you search Fiamm on eBay you may be asked for big bucks but if you...
  10. Replies
    16
    Views
    976

    Wheel mystery

    A friend of mine is in hospital right now after experiencing the rear wheel on his 98 RT coming off. There was no warning. Luckily he was only travelling at about 15mph so his injuries are minimal,...
  11. Replies
    11
    Views
    1,637

    Arthritis in the hands

    So what if anything are you doing to relieve the pain. I too have arthritis in my finger joints. Have been taking calcium supplements and Glucosimine and Chondritin daily. Hasn't cured my ailment but...
  12. Replies
    0
    Views
    445

    2AV54 Hall Effect Sensor

    I need an old/used backing plate to allow me to build a complete HES that I could switch out whenever the time came. Does anyone have one I could use.
  13. Replies
    15
    Views
    3,119

    ABS sensor. Check installation and required gap.

    ABS sensor. Check installation and required gap.
  14. Replies
    10
    Views
    1,331

    Completed the bleeding of all 4 circuits this...

    Completed the bleeding of all 4 circuits this weekend and what a difference it made both physically and emotionally.
  15. Replies
    10
    Views
    1,331

    Thanks Ken. I will do that just curious about the...

    Thanks Ken. I will do that just curious about the fluid container above the master cylinder.
  16. Replies
    10
    Views
    1,331

    Brake bleeding question

    My last BMW was a 1995 R1100RS. When I bled the rear brake, I simply opened the bleed valve in the piston assembly and pressed down on the brake lever and kept the brake fluid topped up. Now on my...
  17. Replies
    1
    Views
    382

    Fork Seal Diameter

    Does anyone know the diameter of a fork seal on a 2004 R1150GS. I need to change mine and want to make a driver before Wednesday since I will be off work till the following Monday but will be...
  18. Replies
    9
    Views
    1,033

    Just make sure you connect them the right way...

    Just make sure you connect them the right way around so when disconnected, the tank does not keep draining. only one of them is a shutoff.
  19. Replies
    9
    Views
    1,033

    http://www.amazon.com/Double-Shut-Off-Connect-Fitt...

    http://www.amazon.com/Double-Shut-Off-Connect-Fitting-Coupler/dp/B0015HOOD6/ref=sr_1_12?ie=UTF8&qid=1329535854&sr=8-12

    I have used these now on my present R1150GS and my last R1100RSL with no...
  20. Replies
    20
    Views
    1,888

    I had this same problem on my 95 RSL. I removed...

    I had this same problem on my 95 RSL. I removed them sanded out the blisters and burnt area. filled the area with a high temp epoxy, sanded and blended to the original pieces then repainted them with...
  21. Replies
    2
    Views
    718

    R1150GS Windshield

    My 2004 R1150GS came with an Aeroflow windshield that, though is very functional, I think makes the bike very ugly. Just my opinion. Is there anybody out there with an old OEM whindshield that they...
  22. Replies
    15
    Views
    3,119

    the tail light bulb is programmed that if the...

    the tail light bulb is programmed that if the stop light filament burns out, the tail light bulb gets more amps or wattage to make it brighter when the brakes are applied. That is why you think that...
  23. Replies
    8
    Views
    1,160

    I did this upgrade on my 95 R1100RS which was NOT...

    I did this upgrade on my 95 R1100RS which was NOT making a noise before the change. However AFTER the change it still did not make a noise. So that's good..right?
  24. Replies
    14
    Views
    1,348

    Same as a Navajo chip but from a different nation.

    Same as a Navajo chip but from a different nation.
  25. Replies
    8
    Views
    1,160

    Left side cam chain tensioner. When engine is...

    Left side cam chain tensioner. When engine is switched off, the oil in the tensioner drains out and then rattles at start up until it refills. The left side tensioner is upside down from the right...
Results 1 to 25 of 233
Page 1 of 10 1 2 3 4