Search:

Type: Posts; User: jbarneshb; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.13 seconds.

  1. I would have waited till I got my seat back...

    I would have waited till I got my seat back before commenting on service. Can't imagine that this will help.
  2. Replies
    23
    Views
    2,579

    What's a CLC?

    What's a CLC?
  3. Replies
    103
    Views
    11,070

    I worry if the cash is all good. Once when...

    I worry if the cash is all good. Once when selling a car, I had the guy go with me to my bank. Their cash counting machine verified that the cash was all good and the count. We then went over to a...
  4. Replies
    103
    Views
    11,070

    You definitely have to be patient when selling...

    You definitely have to be patient when selling bikes. I just now sold a 78 R100s which I've owned for a little over 2 years and put about 13k miles on. I first put it up on Craigslist and ADVrider...
  5. Replies
    4
    Views
    354

    brake pad squeal

    I rebuilt my master cylinder, wheel cylinders and replaced the front brake pads with Ferodo155 pads. After 20 or 30 miles it developed a squeal at about 10-15 mph down to a stop. I removed them...
  6. Replies
    131
    Views
    12,534

    You say that the Siebenrock pistons are the same...

    You say that the Siebenrock pistons are the same for both sides you just needed to make sure the pockets were pointed the right way. Is that the same with stock pistons? I've been told by a local...
  7. Replies
    131
    Views
    12,534

    You put pistons on rods first and then slid...

    You put pistons on rods first and then slid cylinders over pistons. If you'd put pistons with one snap ring installed inside the cylinder first, slid them together over rod and then installed wrist...
  8. Replies
    131
    Views
    12,534

    I'm curious after reading your article on oil,...

    I'm curious after reading your article on oil, what type are you going to be using?
  9. Replies
    20
    Views
    1,323

    I had to ship a seat to TX from CA that I was...

    I had to ship a seat to TX from CA that I was trading. I checked with UPS and it was going to be $46. USPS was going to be $44. FedEx was $18.
  10. Replies
    35
    Views
    3,319

    Well I didn't get lucky. I noticed fluid level...

    Well I didn't get lucky. I noticed fluid level had gone down a little in clutch resovoir. I couldn't see anything at cylinder on handlebar so I pulled the slave cylinder. It was leaking. I bought and...
  11. Replies
    35
    Views
    3,319

    I pulled my slave cylinder off and could see no...

    I pulled my slave cylinder off and could see no leakage. I reprimed it with a syringe and flushed it a couple of times with Magura Blood Mineral Hydrualc fluid. It operates the same as before. After...
  12. Replies
    35
    Views
    3,319

    Does anyone else want to rub salt in my wounds? I...

    Does anyone else want to rub salt in my wounds? I know it was my fault. After doing it I did see the warning on cap saying to use mineral oil. I had only owned one bike before with a hydraulic clutch...
  13. Replies
    35
    Views
    3,319

    Maybe they didn't need to use brake fluid in this...

    Maybe they didn't need to use brake fluid in this application but in the interest of making things simpler and more idiot proof, I wish they would have. Is mineral oil any better than brake fluid in...
  14. Replies
    35
    Views
    3,319

    I hope I can save some of this system. I've...

    I hope I can save some of this system. I've checked the prices of clutch cylinder, hose slave cylinder and hose and it comes to almost $800. I'm going to try to flush and bleed system with correct...
  15. Replies
    35
    Views
    3,319

    brake fluid in clutch

    I mistakenly flushed my clutch with brake fluid a few months ago. It felt different so I tryed to bleed it again when I let the resevoir run dry. It was then that I realized I should have been using...
  16. Replies
    12
    Views
    1,295

    I don't think I'd remove the cannister myself....

    I don't think I'd remove the cannister myself. How high is too high when filling that might cause fuel to get into cannister? I've been filling about half way up the tube inside top of tank.
  17. Replies
    12
    Views
    1,295

    Other than access to your front shock, why would...

    Other than access to your front shock, why would you want to eliminate the charcoal cannister? Does it affect the performance or driveability?
  18. The dealer I go to wanted $110 for this service...

    The dealer I go to wanted $110 for this service which made it worth my time to do it myself. Most of the regular maintenance is pretty straight forward. Just can't reset that service reminder without...
  19. Replies
    12
    Views
    1,379

    I have one I'm trying to sell in So Cal if you're...

    I have one I'm trying to sell in So Cal if you're interested. jbarneshb@verizon.net
  20. Replies
    4
    Views
    798

    Well I put the rebuild kit in, bled it again and...

    Well I put the rebuild kit in, bled it again and it works good. Master cylinder worked fine before I rebuilt wheel cylinders and replaced brake pads so it seems funny that it would go bad but it...
  21. Replies
    4
    Views
    798

    I deciced to rebuild the master cylinder but it...

    I deciced to rebuild the master cylinder but it looked ok so I think it probably did have some trapped air. It doesn't have banjo bolts rather the hoses themselves screw into the master cylinder....
  22. Replies
    4
    Views
    798

    ATE Master Cylinder

    After rebuilding my ATE wheel cylinders and replacing my front brake pads I tried bleediing them both with a vacuum pump and by hand. I can't get them to pump up right. I notice that when I squeeze...
  23. Replies
    9
    Views
    1,129

    Is the seat the standard height? Did you have...

    Is the seat the standard height? Did you have your old seat redone?
  24. Replies
    2
    Views
    658

    Seibenrock Kits

    Has anyone had any personal experience with the Seibenrock replacement nikasil cylinder/piston kit offered by Ted Porter's Beemer Shop. I'm thinking of replacing those on my 78 R100S not for any...
  25. Replies
    12
    Views
    1,378

    I Should have checked there before ordering from...

    I Should have checked there before ordering from Motorrad and I would have saved $43.
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4