Search:

Type: Posts; User: Blacque Jacque Shellacque; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    12
    Views
    495

    Great to hear the RID's working again. Pulling...

    Great to hear the RID's working again. Pulling the fuse removed the power from the RID, which allowed it to reset. The R & R of the fuse doesn't confirm nor eliminate it as the culprit. That being...
  2. Replies
    12
    Views
    495

    Have you try pulling Fuse 3 which removes 12...

    Have you try pulling Fuse 3 which removes 12 volts from the RID? If the RID does not reset, the electronic within are likely fried. As others have posted, the root cause is most likely a bad...
  3. I can't help but wonder if its one of the timing...

    I can't help but wonder if its one of the timing chains rattling around? Pulling in the clutch changes the load on the engine slightly. Perhaps smoothing the idle a bit?
  4. Replies
    70
    Views
    2,503

    Just curious how you maintained a functioning...

    Just curious how you maintained a functioning brake light with the ABS unit removed?
  5. This is great work and thoughtful analysis....

    This is great work and thoughtful analysis. Thanks.
  6. Replies
    70
    Views
    2,503

    I replaced the iABS servo in my 02 RS with a new...

    I replaced the iABS servo in my 02 RS with a new one five years ago. I don't have a GS911 and I didn't didn't bring it to a dealer for a bleed test. It's been working just fine since I installed it....
  7. Judging from the symptoms your listed, it would...

    Judging from the symptoms your listed, it would seem iABS controller is fried. When the servor failed on my RS, I picked up 2 used units that supposedly worked. The first one never made it past the...
  8. Replies
    70
    Views
    2,503

    From my own experience, if the iABS servo runs...

    From my own experience, if the iABS servo runs continuously, it's failed. Replacing the brake lines will not resolve this problem. If don't doubt that brake lines deteriorate over time, but I really...
  9. Replies
    56
    Views
    2,846

    I guess I'm out in left field all alone! When...

    I guess I'm out in left field all alone! When you post a comment or picture on the internet, you can't get it back. Once it's out there you lose control of it. Someone may use it and abuse it. It's...
  10. Replies
    56
    Views
    2,846

    Perhaps I own a small side business repairing...

    Perhaps I own a small side business repairing motorcycles, and I have a website. I decide to post a picture of myself with my BMW bike and the roundel can be seen. What then? It's my picture, my...
  11. Replies
    56
    Views
    2,846

    So now I am curious. My BMW came with at least 4...

    So now I am curious. My BMW came with at least 4 rondels. Who owns them, BMW or me? Since they sold it to me, and I think I rightfully own it, am I not free to do with it as I please?
  12. Replies
    56
    Views
    2,846

    Right on. If someone was trying to sell a knock...

    Right on. If someone was trying to sell a knock off car or bike with a BMW logo, that's a an entirely different ball of wax. Selling a handful of toys doesn't compete with BMW, and they likely...
  13. Replies
    9
    Views
    490

    I would also agree with Rogers recommendations. ...

    I would also agree with Rogers recommendations.
    I would also add motobins depending on what you might need. Surprisingly fast delivery considering the parts have to cross an ocean.
    ...
  14. Replies
    56
    Views
    2,846

    BMWNA has no standing in Canada. Why the OP...

    BMWNA has no standing in Canada. Why the OP called them is puzzling. If they have lawyers, they can keep keep on playing solitaire because they can't practice in any Canadian court without passing...
  15. Replies
    56
    Views
    2,846

    I would just use it. You may fly under the radar...

    I would just use it. You may fly under the radar and they don't notice. If not you get some nasty and threatening letters. So what.
  16. Replies
    1
    Views
    169

    Check the plastic all around the circumference of...

    Check the plastic all around the circumference of where the cover closes and seals with the case. Check for cracks or other damage, etc. Pay attention near the bottom and at the hinges. I recently...
  17. Years ago I replaced all the bleed screws in my...

    Years ago I replaced all the bleed screws in my 1150RS with speed bleeders. I didn't find them very effective. When bleeding, more fluid seemed to leak out the base then out the valve on top. When...
  18. I have one of these on my 1150RS. It works well...

    I have one of these on my 1150RS. It works well and hasn't fallen off. Then again I did follow the instructions and used loctite. It's not made of rubber, but there is a foam pad under the stands...
  19. Replies
    82
    Views
    3,768

    $2700 for a clutch replacement? Is this correct...

    $2700 for a clutch replacement? Is this correct and not a typo?
  20. Well done! That make's a lot of sense. I was...

    Well done! That make's a lot of sense. I was wondering how any single ball bearing could have possibly fallen out of any of the cage's from any of the shaft bearings!
  21. Maybe it?s just a matter of perspective of what...

    Maybe it?s just a matter of perspective of what BMW is today from what it was in the past? For example. Back in the 80's BMW advertised longevity and durability. I believe they even showed riders...
  22. BMW reported sales of approximately 75 billions...

    BMW reported sales of approximately 75 billions Euros in 2013. That's about $100B in US currency. Do you really thing they care that much about selling a handful of Jackets and boots?
  23. It is my understanding that it's against Harley...

    It is my understanding that it's against Harley code to wave at non Harley riders. Those that do, likely have poor eyesight or have simply not noticed what you are riding. The cylinders on my...
  24. I honestly don't see much of a market in North...

    I honestly don't see much of a market in North America for a 300CC motorcycle that will likely cost $6000.
  25. Very interesting. I have been considering the...

    Very interesting. I have been considering the idea of sending my shocks in for a rebuild. When I spoke with John at the bike show, he had a Elkins rep in his booth. Nice looking shock, with both...
Results 1 to 25 of 103
Page 1 of 5 1 2 3 4