Search:

Type: Posts; User: khelsea; Keyword(s):

Search: Search took 0.05 seconds.

  1. Replies
    5
    Views
    737

    [ QUOTE=Happy Wanderer;829500]When you...

    [





    QUOTE=Happy Wanderer;829500]When you pull off the right side fairing there are two rubber lines cable tied to the frame coming from under the tank and next to the airbox. There are in...
  2. Replies
    5
    Views
    390

    I'm going to try a propane test to see if it's...

    I'm going to try a propane test to see if it's really sucking air. I checked it again this morning and I can get it to wiggle but not very much. Khelsea
  3. Replies
    5
    Views
    390

    1150rt throttle plate shaft

    I can move my left hand throttle plate shaft up and down. Would that be causing enough of a vacuum leak to cause a problem? Bike has 36K on it. The right hand is tight. The bike has a heavy vibration...
  4. Replies
    5
    Views
    960

    Scott How did your fuel injector cleaning go?...

    Scott How did your fuel injector cleaning go? Khelsea
  5. Replies
    9
    Views
    746

    My thoughts exactly, with every tire change....

    My thoughts exactly, with every tire change. Could have solved my buzzy problem if I survived. Khelsea
  6. Replies
    9
    Views
    746

    tire pressure loss

    Just an experience to share. Sunday I check TP and find the front down 4 PSI so fill it. Yesterday I'm doing 90MPH runs trying to blow the carbon out? So 3 hours later I went to leave work and the...
  7. Replies
    37
    Views
    2,360

    Well I thought I had it but still vibs at 3250...

    Well I thought I had it but still vibs at 3250 and buzzin the rest. I agree with Paul on the syncro hiding other probs and everyone that 3250 is too low in 6th. So anyway I've done the techcron...
  8. Replies
    37
    Views
    2,360

    My 1150 it surged terribly until I did a very...

    My 1150 it surged terribly until I did a very carefull valve adjust and syncro then it went away or at least 80% so somewhat satisfied. I actually would kill on occasion. So anyway my vibration at...
  9. Replies
    37
    Views
    2,360

    Just a question but on my 02 1150 to reset the...

    Just a question but on my 02 1150 to reset the motronic is that a 2 or 4 and is it the same rest procedure ie pull fuse 5 and twist? I will have more to this story tommrow. Those QD's get them...
  10. Replies
    37
    Views
    2,360

    Like Paul says they should run on a flat road at...

    Like Paul says they should run on a flat road at 3200 65mph without vibs. Should feel power impulses if you pour the coals to it only. There's been alot of talk about injectors here but wouldn't...
  11. Replies
    37
    Views
    2,360

    [I'm sorry for not telling about the mileage it's...

    [I'm sorry for not telling about the mileage it's 35K and if you remember I spoke about something I did different from before and adjusted the left throttle cable which exasperated maybe this...
  12. Replies
    37
    Views
    2,360

    I hear but I've driven this m/c for 10K this year...

    I hear but I've driven this m/c for 10K this year and the vibration wasn't this bad until now so something has changed or should I say it's something I've changed and now I can't seem to find out how...
  13. Replies
    37
    Views
    2,360

    So really the answer is all the 1150's have a...

    So really the answer is all the 1150's have a severe vibration at 3200 in any gear loaded or unloaded????
  14. Replies
    37
    Views
    2,360

    1150rt 3200 rpm vibration

    Not having the ability to drive another one to compare with do all the 02 1150rts have a engine vibration at 3-3200 rpm? I've done a spline lube, valve adjust and sync. It's better but after a 40...
  15. Replies
    8
    Views
    1,406

    I got it

    OK i got it. Both cables had less than 0 play so after adjusting the BBS's as I went to sync the cables it was changing the BBS setting on the manometer, now all is well.
    A question on my other...
  16. Replies
    8
    Views
    1,406

    2002 1150RT TB adjustment 32K

    I've set my valves and am now ready to do TB adjustment. Shouldn't the left cable have a certain amount of slack? I did the adjustment last week but I couldn't seem to get the manometer to be even on...
  17. Replies
    7
    Views
    579

    FYI No reset of the abs unit was required but...

    FYI No reset of the abs unit was required but with the battery disconnected I suppose I should have done the twist of throttle to reset the TB's. Thanks again Josh
  18. Replies
    7
    Views
    579

    YIPPIE!!!!!!!!!!! Josh your the man. You just...

    YIPPIE!!!!!!!!!!! Josh your the man. You just saved me a 400 mile trip to the dealer and the smirk on the mechanics face, hey DA you pinched off this wire, should of brought it to us first and saved...
  19. Replies
    7
    Views
    579

    I see your point. I'll check it this morning. Did...

    I see your point. I'll check it this morning. Did you have to do anything to get the abs system to reset? Thanks
  20. Replies
    7
    Views
    579

    I thought about that too but I ohmed out the...

    I thought about that too but I ohmed out the switch and it's good. I also don't have a rear brake lite when i apply the rear brake but I do with the front. Thanks for your response. Right now I have...
  21. Replies
    7
    Views
    579

    2002 1150rt abs trouble

    Just got done doing the spline lube and went real well, splines looked great and now shifts better than ever. I do have a 4HZ flash and warning lite on and no rear assist on the brakes. I can hear...
  22. Replies
    1
    Views
    332

    Transmission guide pins 02 1150RT

    Anybody know the metric size of the bolts that can be used for guide pins on a spline lube ? I know they need to be approx 4in long. Tnx, Lanny
  23. Replies
    2
    Views
    848

    I am and unfortunatly I'm already speeding on our...

    I am and unfortunatly I'm already speeding on our secondary roads. I'm aware that to keep low rpm power pulses off the trans bearings it's good to let them rev. I made it 50K with my 90/6 with no...
  24. Replies
    2
    Views
    848

    Paul, Anton?

    OK Lets go over this again. Shifting into 1st rolling sounds like grampas old ford truck in granny gear, 2nd is clean 3rd has a high pitched gear noise 4th good 5th good 6th has a high pitched whine...
Results 1 to 24 of 24