Search:

Type: Posts; User: sy308moa; Keyword(s):

Search: Search took 0.05 seconds.

  1. Replies
    33
    Views
    4,633

    Update on the filter. Rag trick did not work. I...

    Update on the filter. Rag trick did not work. I needed to use the drill into filter trick. I took my filter wrench and drilled 6 holes corresponding with the 6 rounded areas in the periphery and...
  2. Replies
    33
    Views
    4,633

    Thanks, guys. Will try the rag first, then with...

    Thanks, guys. Will try the rag first, then with screws into filter. Looks like will need to bring the wrench inside to the drill press and modify it. Lots of good ideas. Will try tomorrow for the...
  3. Replies
    33
    Views
    4,633

    Can not remove oil filter

    The filter has been on for many years. I can't get it to turn. Even turned bike on the side to help get leverage. Suggestions???
  4. Thanks, what I have done so far is to change the...

    Thanks, what I have done so far is to change the master cylinder by getting some more slack in the heated grip wires and cut the wire. I cut lots of wire ties to get the slack. I will have to...
  5. Heated Grip Removal? (change master cylinder)

    Bike number one (R1100RS) had a totally bad master cylinder. It is changed, flushed and all OK. Bike number two, R1100RT, has heated grips. I have the cylinder all ready to replace but really need...
  6. Replies
    7
    Views
    978

    Thank you for the clarification and assistance.

    Thank you for the clarification and assistance.
  7. Replies
    7
    Views
    978

    Thank you. The bike in question is an early one,...

    Thank you. The bike in question is an early one, MY 1985 purchased in 1984 (by me original owner). Is this then still repairable???
  8. Replies
    8
    Views
    617

    Thanks. I will replace the brake lines and check...

    Thanks. I will replace the brake lines and check out Beemerboneyard for master cylinder replacement/rebuild. I have an 1100RT and the front brake lever has been acting funny. Sometimes I have to...
  9. Replies
    7
    Views
    978

    Thanks. I will order the gasket. It is most...

    Thanks. I will order the gasket. It is most likely the problem, otherwise will look to epoxy the wiring in place.
  10. Replies
    7
    Views
    978

    '85 K100 Gas Leak at electronics plug

    Hi. Looking to Macgyver my gasoline leak from the electronics connection in the bottom of the K100 gas tank. There is a slow leak and the smell is bad for the house. The electronics and electrical...
  11. Replies
    8
    Views
    617

    1994 Front Brake will not release

    I just picked up a 1994 bike (low mileage in nice shape but it sat for last 3 years) and when riding home, front brake would not release calipers. Brake handle is soft with little resistance too. I...
  12. Replies
    3
    Views
    708

    Thanks for the replies. I was able to get the...

    Thanks for the replies. I was able to get the injector rail off and the gaskets all changed. There must have been a significant leak for some time. The number 2 cylinder gasket which fit into the...
  13. Replies
    3
    Views
    708

    Changing fuel injector gaskets?

    The second problem with K100RS is some fuel leaking is noted around the fuel injectors. I have 8 new BMW gaskets, 2 per injector, and was looking for tricks, advice or guidance as how to move the...
  14. Replies
    6
    Views
    4,938

    K100 throttle body adjustment?

    My K100RS was returned to me from service with the complaint of a poor fast idle. It now idles at 1500 and can not be adjusted downward by the common adjusting screw which moves the throttle bodies....
Results 1 to 14 of 14