Type: Posts; User: Spinakr; Keyword(s):
Does anyone know if a NEW clip-on tank bag from a 2012 R1200RT will fit on an older 2005 R1200RT?
Get out of Tillamook on hwy 131 west and see Cape Lookout / Cape Kiwanda / Netarts Bay and Pacific City.
If you're lucky you can catch the flat bottom Dory Boats sliding in on the surf and onto the...
I have an RT now. I think something smaller like the G650GS or even the F700GS would be great.
I live near the foothills of the Cascades in SW Washington. I've wanted to explore those for a LONG...
Well, I'm sure the power to the fuse block is direct to the battery. Last time I looked; It appeared the fuse block trigger wire ran to a wire connected the alarm system. I boght the bike in August...
Power source is a switched fuse block as recommended by Skene. Fuseblock is made by touratech.
The fork Mounted Photons are connected with provided IQ-150-TS Controller.
The upper Turns were also connected in strict accordance with the leads from the IQ-150-TS Controller.
I also used the...
I just purchased a new Optimate 4 CAN-bus compatible battery charger, with the charger in CAN-bus mode I plug into the power port on the clutch side fairing. After...
Last night I got it figured out and got the TB's sync'd pretty close at 1800 - 2500 - 3000 - 3500 - 4000rpm.
I had to go back & forth several time between the 2 sides.
The only concern I have is...
I'm sure I already know this, but just making sure.
Is the GS-911 "Idle Actuator Calibration" performed with the engine off?
I saw that the instructions indicate the "Lock Idle Actuators"...
Thanks again marchyman.
I'll check that cable play tonight.
I forgot to mention, before attempting the throttle sync I adjusted the valves following VonBaden's video to a T.
Are you saying that the throttle cables at the bodies need to...
I am unable to balance the throttle bodies on my '05 R1200RT.
With engine off, I used a GS-911 to park/Sync the stepper motors,
then with engine off I connected a Harmonizer and...
I had a REAL hard time trying to get the supplied connectors onto the wires coming off the back of the high beam plug.
So, I took a couple of male spade connectors, then, using a couple of pairs of...
It was looking like that was my only option.
Has anyone installed a flash2Pass transmitter on an R1200RT?
I really can't see how I'm going to tap into the high beam wires off the back of the bulb.
There's just no room to shove the Flash2Pass...
Also be advised that as things have gotten even TIGHTER over the last year or so...
Some municipalities are now writing tickets for even 4 miles an hour over in the city limits at posted speeds of...
So you know how bad that paint job looks huh?
I've found a fairly nice workbench at Costco, it's not on the Costco website, but very similar to THIS ONE made by Whalen; Just a bit fancier with stainless front pull out drawers and 2 sidemount, or...
My '05 R1200RT had clear signal lenses with amber (PY21W) bulbs when I purchased it.
I changed out the Amber bulbs with BAU15S-x18-T: 18HP-LED 1056 LED Tower bulbs from here:...
I need to drain the fuel from the tank on my '05 R1200RT.
Since I need to remove the tank from the bike so I can perform a brake flush, I figured I go ahead and fix the cracked fuel pump fitting...
I thought it was just something wacky with my browser
I needed to get the tire off the wheel so I could install a new Michelin PR3.
I wasn't sure id I'd muck up the rotors with the tire irons/spoons if I left them on, so I pulled them off. I've never...