Search:

Type: Posts; User: MUSICMAN; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    3
    Views
    465

    Oil spray Left Side

    My 95 R1100 GS with 115,000 happily traveled miles blew oil on to my left boot and shin yesterday. As soon as I noticed the leak (my toes slid of the shift lever) I had about 6 miles to go to home....
  2. Replies
    1
    Views
    450

    K75 clutch messed up?

    I recently installed a used clutch disc that is practically brand new on my 93 k75 from someone on this list serve. Before my disc splines had been eaten alive and ruined the input shaft on the...
  3. Replies
    3
    Views
    463

    Installing Swing arm bearings 93 K75

    I have the old bearings out of my 93 K75. Haven't looked at the Clymer in detail yet. Do I need to pack the bearings with grease and does the grease shield (plastic black piece) pop on last? Any tips...
  4. Replies
    1
    Views
    506

    '93 K75 Removing swing arm bearing?

    93 K75
    I rented a slide hammer wheel hub removal tool from Advance Auto and was able to use the little hook to remove one bearing including the race however the other side left the race in and I...
  5. Replies
    2
    Views
    572

    Balancing Clutch?

    93 K75
    How do I balance a clutch assembly without all the marks?
    Clutch is out, I marked it along time ago but marks are gone.
    No I didn't mark it before taking it out, woops

    I have a factory...
  6. Replies
    5
    Views
    907

    R1100 Compression test low

    I finally got around to checking my compression tonight. 95 GS 110,000 miles.

    Symptoms, smoking a lot upon start up, friends have also noticed a wee bit of oil burning as they ride behind me. I...
  7. Replies
    17
    Views
    3,012

    adv

    thanks for the info. I am a member.
  8. Replies
    17
    Views
    3,012

    R1100 Throttle body rattle

    My right throttle body on my 95 GS, seems to be rattling inside. At one point I replaced a few things inside in it but can't remember what they were (butterfly maybe and a few other things?)

    Bike...
  9. Replies
    18
    Views
    2,501

    bumpity bump bump

    bumpity bump bump
  10. Replies
    18
    Views
    2,501

    waiting is fullness

    I know you're busy. I'm really looking forward to the read when you can.
  11. Replies
    18
    Views
    2,501

    Gone...Like A Nixon File (John Hiatt)

    Thanks for updating us Lee, I'm deep in bookkeeping as well, rounding the corner finally.

    Ya, those splines are long gone. I was getting some sound from that area and was going to check it out...
  12. Replies
    18
    Views
    2,501

    thanks for the clarification. I wonder why it's...

    thanks for the clarification. I wonder why it's now showing up. I did replace the entire clutch assembly about 25,000 miles ago for a worn friction disc and very slight warping on the plates but the...
  13. Replies
    18
    Views
    2,501

    lets see if this works

    Here are the clutch splines (lack of), very rounded (the red is my lift)

    http://i482.photobucket.com/albums/rr188/musicman92564/2012-04-02_20-32-47_451.jpg

    On the input shaft upon closer...
  14. Replies
    18
    Views
    2,501

    honda

    I'm looking forward to the write up too as I bet many others are.

    I used the Honda Molly paste and I've always had good luck with it.

    Andy
  15. Replies
    18
    Views
    2,501

    I wonder what the reason would be to replace the...

    I wonder what the reason would be to replace the flywheel and clutch carrier?
  16. Replies
    18
    Views
    2,501

    the clutch plate is complete toast, will get...

    the clutch plate is complete toast, will get replaced. I'm hoping to be able to reuse the spring, plates and spring
  17. Replies
    18
    Views
    2,501

    k75 clutch splines rounded

    93 K75, 67,000 or so miles.
    Last year my K bike had no drive power getting onto a highway.
    Finally pulled it apart last week and my clutch splines were practically non existent and dry as a bone....
  18. Thread: New MOA Logo

    by MUSICMAN
    Replies
    332
    Views
    21,453

    Yep!

    Yep!
  19. Replies
    5
    Views
    874

    seems my raised shoulder on the pulley got...

    seems my raised shoulder on the pulley got sheared off?



    Andy
  20. Replies
    5
    Views
    874

    pulley

    I'm assuming the hall cup is spot welded to the pulley or is separate?
  21. Replies
    5
    Views
    874

    Mud, AAA, Vermonters and Hall Sensor.

    Long. (I'm in a writing mood) Skip all and see questions at bottom?

    95 R1100 GS 108,000 miles.

    Yesterday we were out for a GS ride near Pownal, VT. Amongst numerous rocky trails that a local...
  22. Replies
    17
    Views
    1,720

    screw drivers?

    Paul any ideas other than flat head screw drivers to pry gently?

    Thank you!
    Andy
  23. Replies
    17
    Views
    1,720

    Removing Final drive bearing?

    I've finally gotten around to removing the large final drive bearing on the crown gear housing but I'm not able to get it off. Everything up to that point has been fine using a heat gun as suggested...
  24. Replies
    18
    Views
    1,847

    American Motorcycle Tire

    I understand that sizes and all effect price of tire. That's why I posted TKC 80 :).

    I ordered them late Friday evening from AMT and they were on my doorstep in Albany, NY this morning.

    Look...
  25. Replies
    18
    Views
    1,847

    thank you

    Thank you for the info. Bike Bandit was about $40 more expensive and then shipping on top of it. SW moto tire was same as my dealer.

    I found American Motorcycle Tire and a pair of Conti TKC 80's...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4