Search:

Type: Posts; User: scottr; Keyword(s):

Search: Search took 0.06 seconds.

  1. Replies
    31
    Views
    2,972

    Pa

    I'd go for PA. I am in the southeastern part of the state----4 hrs to the Finger Lakes area, 3 hrs to Shenandoah/Harpers Ferry & BRP, close to NJ/DE/MD seashores and lots of great riding throughout...
  2. Replies
    2,764
    Views
    896,630

    Sticky: restored 74' R90/6

    33088

    Courtesy of Bud H. in Downingtown, PA and Mac K. Glenmoor, PA. The bike belongs to my brother.
  3. Replies
    5
    Views
    1,007

    Thanks for the great tips and info. Scott R

    Thanks for the great tips and info.

    Scott R
  4. Replies
    5
    Views
    1,007

    75' R75/6 caliper adjustment

    How critical is the caliper adjustment for good braking on a 75' R75/6 with an ATE caliper?

    I've rebuilt the caliper and master cylinder and still seem to have not so effective front braking. The...
  5. Replies
    11
    Views
    1,611

    If you are looking for a decent campground in...

    If you are looking for a decent campground in Maine before heading to New Brunswick and then Nova Scotia, the Cobbscook State Park on Rte 1 just before Calais (entry point into Canada) is highly...
  6. Replies
    4
    Views
    554

    Thanks for all the help---it is much appreciated.

    Thanks for all the help---it is much appreciated.
  7. Replies
    4
    Views
    554

    /6 Master Cylinder problem

    Need advice on where to obtain the O ring that sits between the master cylinder and fluid reservoir for a 75' R-75/6. BMW does not sell the O ring and it is not included in the master cylinder...
  8. Replies
    6
    Views
    2,218

    2011 Rally-Bloomsburg, PA

    According to the Owner's News, the 2011 rally will be in Bloomsburg, PA. What a great spot!!!!
  9. 07' gs

    Any idea why BMW moved to the Michelin tires for the 07' GS? My front tire is developing some wierd wear patterns with 8K on the odometer.
  10. Replies
    25
    Views
    1,747

    Come out to Lancaster County, PA and ride the...

    Come out to Lancaster County, PA and ride the twisties around the beautiful farmland encountering an occasional Amish buggy.
  11. Replies
    2
    Views
    790

    /6 Master Cylinder Rebuild

    Any suggestions on how to install the o rings on the new master cylinder piston that comes with a master cylinder rebuild kit? I've tried various "stretching" methods only to abandon the ordeal so as...
  12. Replies
    3
    Views
    3,125

    Poll: R1200 GS Bars

    I bought the Hepco & Becker bars from the dealer for $250-300, I don't recall the exact amount. They went on very easily after I bought a good set of Snap On Metric hex sockets to use when you remove...
  13. Replies
    11
    Views
    2,478

    Pushrod seals

    If you are not replacing the rings, you can merely slide the heads out enough so that the push rod tubes will clear the engine housing. Take the old seals off and put the new ones on. There is a good...
  14. Replies
    18
    Views
    9,974

    Keep up posted on your progress. I'll be doing...

    Keep up posted on your progress. I'll be doing the same thing to my Dad's 74' R90/6 I am restoring.
  15. Replies
    0
    Views
    808

    R1200 R passenger pegs

    Anyone have experience with lowering the passenger pegs on an R1200 R? I am going to look at one on Saturday and my wife is about 5-8 and concerned the pegs might be too high and uncomfortable.
    ...
  16. Thread: Gen light is on

    by scottr
    Replies
    5
    Views
    914

    You could also check the diode board as a...

    You could also check the diode board as a preventive measure.
Results 1 to 16 of 24