Search:

Type: Posts; User: jsf14469; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.06 seconds.

  1. Replies
    12
    Views
    829

    Gentlemen, Thanks for the advice

    Gentlemen,
    Thanks for the advice
  2. Replies
    12
    Views
    829

    1982 R100RS clock kaput

    Are there replacements? How does the clock come out? Not much space on the back side?
    Thanks for some advice
  3. Replies
    7
    Views
    502

    Thanks for the input

    Thanks for the input
  4. Replies
    7
    Views
    502

    Nikasil

    How do you which are Nikasil?
  5. Replies
    7
    Views
    502

    1982 R100RS Cylinder Honing Question

    Currently heads are off for valve work. Examination revealed badly worn exhaust valves at 75,000 miles. Piston crowns have some carbon and intend to remove and clean them. If pistons removed from...
  6. Replies
    1
    Views
    293

    snow flake rear & Bridgestone Spitfire

    Have mounted a few of these and each time quite a challenge to set bead. Last tire mounted had an undetermined air pressure (greater than 50 Lb gauge at any rate) and after quite a bit of vigorous...
  7. how to replace & adjust throttle cables 1982 r100rs?

    New cables and not sure how to adjust the the connector under the tank where single cable splits to separate carb cables
  8. Replies
    8
    Views
    1,233

    Pictures and all. Again thanks. Will have a go at...

    Pictures and all. Again thanks. Will have a go at it.
  9. Replies
    8
    Views
    1,233

    How do you get the frozen nut off the stud...

    How do you get the frozen nut off the stud without buggering the threads?
    Replace may be the best.
    Appreciate your replys
  10. Replies
    8
    Views
    1,233

    Lew, Appreciate the reply. When using Loctite is...

    Lew,
    Appreciate the reply. When using Loctite is there a certain cleaner that should be used on the threads to be secured before applying Loctite?
  11. Replies
    8
    Views
    1,233

    Triple tree stud loose

    Installing stainless kit on 1971 R75/5 and removing old nut from lower triple tree, however stud turned out rather than nut coming off. Was able to simply reinstall as though it was a bolt, but what...
  12. Replies
    4
    Views
    663

    Thanks for your reply. Pretty sure not spline...

    Thanks for your reply. Pretty sure not spline lube. Put on tire last spring and lubed splines with a bit of Never Sieze not grease. Quick look at some of the articles left me dazed. Perhaps a good...
  13. Replies
    4
    Views
    663

    Snowflake bearings

    Getting ready for the riding season, putting on new tires. Wheel bearing grease found inside the rear rim. Can this be just a bad seal? Can the bearing be repacked and a new seal put in? Would it be...
  14. Replies
    7
    Views
    1,558

    Kurt Thanks for the quick reply. Made for some...

    Kurt
    Thanks for the quick reply. Made for some very interesting reading. Did not know this was such a volatile subject. There is some heat out there. Thanks again
  15. Replies
    7
    Views
    1,558

    Snowflake rims - tubeless?

    About to put new tires on 1982 r100rs with snowflake rims. Have been told that they can be run tubeless and that it may be good idea to file flat the stem mounting area and paint the inside due to...
  16. Replies
    2
    Views
    698

    How to clean snowflake wheels

    Acquired a 1982 100RS last fall. Bike is victim of neglect. Wheels are a mess, especially the rear. Any good methods of cleaning or cleaners recomended - short of bead blasting?
  17. Thread: Timing light

    by jsf14469
    Replies
    14
    Views
    1,482

    Have replaced replaced kaput stock electronic...

    Have replaced replaced kaput stock electronic ignition with Motorad Elektrik unit which has electronic advance. Set timing about in midway of adjustment and bike starts and runs reasonable. How do...
  18. Thread: Timing light

    by jsf14469
    Replies
    14
    Views
    1,482

    sounds as though Sears inductive the way to go....

    sounds as though Sears inductive the way to go. Thanks all.
  19. Thread: Timing light

    by jsf14469
    Replies
    14
    Views
    1,482

    Timing light

    In need of strobe light. Cost runs between $20 to hundreds. Only advice I have seen is do not go cheap it may not be bright enough. How does one know without trial and error purchase? Is brightness...
  20. Replies
    5
    Views
    1,391

    Thanks for the update on original BMW shield. I...

    Thanks for the update on original BMW shield. I had simply assumed that only aftermarket would be available. Even the price is competetive.
  21. Replies
    5
    Views
    1,391

    The short Clearview windshield looks close top...

    The short Clearview windshield looks close top stock, however I do not have a stoch to compare with. The Motobins definitely looks taller than stock. Currently the bike has a windshield that is...
  22. Replies
    5
    Views
    1,391

    R100RS Windshield

    Looking for original winshield for 1982 R100RS. Are new available? Good aftermarket?
  23. Replies
    12
    Views
    1,635

    Ignition, Diode Board and Oil Cooler

    Acquired 1982 R100RS last fall. Had a great 1000 miles before it stopped running. No spark. Appears that the bean can ignition ignition has given up. Considering the Alpa Ignition for replacement....
  24. Replies
    17
    Views
    1,550

    Appreciate the reminders about the battery...

    Appreciate the reminders about the battery ground. That circular connector at tranny is a pain in the neck to disconnect having to back the screw all the way out to remove ground. Is there any...
  25. Replies
    17
    Views
    1,550

    New to RS world ???

    Just got a 1982 R100RS. Wife surprised me, knowing I had long admired that model, when she became aware of a fair deal (42k miles for $2500) and had it delivered to our house by riding buddy. That...
Results 1 to 25 of 35
Page 1 of 2 1 2