Search:

Type: Posts; User: 85343; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.04 seconds.

  1. Replies
    192
    Views
    12,318

    Several years ago my 95 R1100RS dropped from...

    Several years ago my 95 R1100RS dropped from mid/upper 40's to low 30's. I remembered reading something years prior that a bad O2 sensor could cause the issue. I replaced the O2 sensor and the...
  2. Replies
    9
    Views
    902

    My 95 R1100RSL has large valves. The parts list...

    My 95 R1100RSL has large valves. The parts list shows large to small valve chage at Oct 1995 production.
  3. Replies
    11
    Views
    993

    I mounted 910's under the turn signals on my 95...

    I mounted 910's under the turn signals on my 95 R1100RSL. I made an aluminum backing plate for inside the fairing. Started with two 7 in x 4 in , .16 in thick plates and cut to fit the shape of the...
  4. Replies
    29
    Views
    2,737

    The parts list shows the engine case changes at...

    The parts list shows the engine case changes at the 12/97 date. I would guess that the the thermostat would not fit in the older case.
  5. Replies
    29
    Views
    2,737

    The diagram for the R1100RS shows the parts used...

    The diagram for the R1100RS shows the parts used from 12/97 on. The early RS's did not have an oil thermostat.
  6. Thread: Sub Frame torque

    by 85343
    Replies
    2
    Views
    500

    47 Nm. I'm in the process of bolting mine...

    47 Nm. I'm in the process of bolting mine together, along with replacing the wiring harness.
  7. Replies
    3
    Views
    839

    Not the same shaft. This was a new replacement...

    Not the same shaft. This was a new replacement for that one.
  8. Replies
    3
    Views
    839

    Drive shaft twist

    I removed the drive shaft from my 95 R1100RSL and discovered the shaft had twisted at the rubber bond sometime this year. I had paint marks on the shaft for phasing during assembly which are now 45...
  9. Replies
    6
    Views
    683

    My m94 transmission oil went to the dark side....

    My m94 transmission oil went to the dark side. The tranny was shifting fine but a little louder. I pulled the tranny over the winter to check for problems. (Long cold winter in VT.) The rear bearing...
  10. Replies
    0
    Views
    328

    Temporary no start, oil temp gauge haywire.

    Yesterday my 1995 R1100RSL would not start on the first try as normal, cold engine. The engine cranked over normally but did not fire. I tried 5 or 6 times over a period of 1-2 minutes then it...
  11. Replies
    6
    Views
    941

    I picked up a spray can of bed liner at the local...

    I picked up a spray can of bed liner at the local NAPA parts store. I sanded the case lids and painted the sealing surface that contacts the gasket then sprayed the lids with several light coats of...
  12. Replies
    5
    Views
    625

    I've had them on my bike for ten years. No...

    I've had them on my bike for ten years. No problems. They work great.
  13. Replies
    2
    Views
    505

    Head gastket reuse?

    Can the head gasket of a 95 R1100RSL be reused? I am going to remove the head and cyclinder to fix an oil weep at the base of the cyclinder. I was shocked to find a new head gasket is over $60.
    ...
  14. Thread: Brake Lines

    by 85343
    Replies
    4
    Views
    574

    I installed Spiegler SS brake lines on my 95...

    I installed Spiegler SS brake lines on my 95 R1100RSL. I also use barbacks for a short time. The standard Spiegler lines work with barbacks without any further modification.

    Kurt
  15. Replies
    0
    Views
    442

    anti rattle spring prevents brake release

    I have a 1995 R1100RSL with 109000 miles. This year I installed Galfer Wave rotors along with a new set of EBC HH pads. I have been using EBC for years and never had a problem. The new EBC pads had...
  16. Replies
    4
    Views
    547

    Oil level drops when cold???

    I have a 95 R1100RSL. Last night I parked the bike after a ride. Side stand for 10 minutes, center stand for 30 minutes then checked the oil, right on the dot. The bike remained on the side stand...
  17. Replies
    3
    Views
    749

    The BMW R1100GS handgards fit the RS. I have been...

    The BMW R1100GS handgards fit the RS. I have been using mine for years on a 95 RSL. They are very effective in cold weather. I take them off during the summer. I got mine at the local dealer.
  18. Replies
    6
    Views
    1,197

    I ordered the bearing from Bearings Specialty,...

    I ordered the bearing from Bearings Specialty, Williston VT, 802-655-2222. The salesman said it is a KYK brand, made in Japan. He said it is a high quality bearing. He said the FAG bearings are made...
  19. Replies
    6
    Views
    1,197

    Buying new FD bearing

    I pulled the FD bearing out last night because I the oil was indicating pending issues. 1995 R1100RSL with 102,000 miles. The bearing was intact but slightly rough. Wear on the teeth indicated it had...
  20. Replies
    5
    Views
    663

    I 'm not sure what happened but the issue is in...

    I 'm not sure what happened but the issue is in the connector that plugs into the turn signal relay. I removed the plastic housing to get a better look at the internals of the connector. On a whim I...
  21. Replies
    5
    Views
    663

    The chips on the circuit board fried. The...

    The chips on the circuit board fried. The contacts are clean. I'll recheck everything this evening. I was working on the bike until 01:00 this morning. The worst part is the sun is shining and it's...
  22. Replies
    5
    Views
    663

    I did all those tests. At least six times. no...

    I did all those tests. At least six times. no short was found. That is what is driving me crazy.
  23. Replies
    5
    Views
    663

    Help, turn signal relay melted?????

    My 1995 R1100RSL has 99600 miles. Last night the turn signals did not work while riding home from work. I figured a fuse had blow so I wasn't too concerned. At home I discovered the fuses were fine....
  24. Replies
    8
    Views
    3,498

    It's a hard knock like a rod knock. I would think...

    It's a hard knock like a rod knock. I would think a rod knock would be heard at more than deceleration. The bearings looked good at 80,000 miles. I replaced the right throttle body when the heads...
  25. Replies
    8
    Views
    3,498

    Both tensioners have been replaced. I would think...

    Both tensioners have been replaced. I would think a tensioner issue would be heard at idle.
Results 1 to 25 of 50
Page 1 of 2 1 2