Search:

Type: Posts; User: sumran; Keyword(s):

Page 1 of 48 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    23
    Views
    1,160

    The under tank master cylinder may get in the way...

    The under tank master cylinder may get in the way of the control unit.
  2. Replies
    1
    Views
    389

    Rick does have them. Last item on this page. ...

    Rick does have them. Last item on this page.

    http://www.motoelekt.com/charging.htm
  3. Replies
    5
    Views
    1,222

    There are numbers stamped on the carbs. On 40mm...

    There are numbers stamped on the carbs. On 40mm carbs it is on the angled part of the casting that runs between the seam of the dome and the top of the venturi. They can be difficult to spot if they...
  4. Replies
    20
    Views
    2,544

    I put an '81 pan on my '80 R100. I did not do it...

    I put an '81 pan on my '80 R100. I did not do it to get additional capacity. I did it because of the barrier wall in the front of the pan. With the old pan I would get an oil light under hard...
  5. Replies
    19
    Views
    1,644

    A couple of things that make a big difference for...

    A couple of things that make a big difference for me.

    I can't get the idle mix right unless I isolate each cylinder.

    When adjusting the throttle cables for sync, I want to add slack cable...
  6. Replies
    40
    Views
    6,419

    +1. They are not all the same. I run mine at...

    +1. They are not all the same.

    I run mine at .10 mm and .20 mm. I change the oil every 2,500 miles and change the oil filter every other oil change. I check the valves every 5,000 miles at the...
  7. Replies
    45
    Views
    2,129

    I would wait until winter to replace the PR...

    I would wait until winter to replace the PR seals. You will be able to fully evaluate the valves once you pull the heads. It doesn't sound like the seals are leaking much and it keeps your options...
  8. Replies
    19
    Views
    1,644

    :laugh Do the new models have a POM sensor to...

    :laugh

    Do the new models have a POM sensor to adjust for this variable?
  9. Replies
    15
    Views
    1,399

    To much to tell and too little data to get to the...

    To much to tell and too little data to get to the answers you want. Find some local airheads and take them with you. In great running condition it is worth less than $3,000. It will take lots of work...
  10. That is very nice. Does it need anything other...

    That is very nice. Does it need anything other than a good cleaning and a battery?
  11. Replies
    19
    Views
    1,644

    There are many approaches to the idle mixture...

    There are many approaches to the idle mixture adjustment. Some of the guys I ride with turn it in until it slows down, then turn it out until it slows down, then leave the screw between those two...
  12. Replies
    15
    Views
    3,567

    Those are some good tips. Thanks for passing them...

    Those are some good tips. Thanks for passing them along.
  13. Replies
    15
    Views
    3,567

    Make sure you stuff some clean shop cloths in the...

    Make sure you stuff some clean shop cloths in the openings behind the timing chain before you try to insert the master link. Otherwise, you may get to remove the oil pan to fish the wandering master...
  14. Replies
    19
    Views
    1,644

    There are large differences is the starting point...

    There are large differences is the starting point on the idle screws, depending on the model of airhead. Kurt's post is very helpful since it gives the setting for your model. I agree with what he...
  15. Replies
    5
    Views
    838

    A properly functioning set of Fiamms will get...

    A properly functioning set of Fiamms will get plenty of attention. You need a heavy circuit (12 or 10 gauge), preferably wired directly from the battery. I fused mine to protect the wiring. Some view...
  16. Thread: High speed miss

    by sumran
    Replies
    8
    Views
    624

    I agree with Dennis. Diaphrams seem like the most...

    I agree with Dennis. Diaphrams seem like the most likely cause for what you describe. It is also very easy to check. If you manipulate the throttle and choke levers on the carb by hand, you may be...
  17. Replies
    23
    Views
    2,552

    I would to see pic's and information on this...

    I would to see pic's and information on this subject. The project bike for me and my son is a LWB 60/5. We like the look of the classic /5 mufflers, but do not know if they will work with a LWB model...
  18. Replies
    14
    Views
    841

    I agree with adding miles a little at a time. You...

    I agree with adding miles a little at a time. You will learn things about your equipment and setup on a 150 mile ride that you can't learn on a 20 mile ride.

    Stretching and water make a big...
  19. Thread: looking

    by sumran
    Replies
    4
    Views
    761

    http://www.airheads.org/component/option,com_conta...

    http://www.airheads.org/component/option,com_contact/catid,80/Itemid,43/

    Here is a list from their website.
  20. Thread: Bike Cover

    by sumran
    Replies
    9
    Views
    720

    I have a Cycle Sak that I bought on ebay and I am...

    I have a Cycle Sak that I bought on ebay and I am quite happy with it. It fits well, has venting and soft lining on the front portions. It is made of a heat resistant nylon/canvas material. I can put...
  21. Replies
    10
    Views
    854

    I can send pics later

    If you haven't got it worked out by Sunday afternoon, I'll be back in town and can take mine apart to send you pic's. I think you might be missing a part if it is giving you a lot of trouble, because...
  22. Replies
    10
    Views
    854

    I'm no help on the lowers as mine doesn't have...

    I'm no help on the lowers as mine doesn't have lowers. On my SS I used the BMW ring. Do you have some other chrome ring or is it the stock BMW unit?
  23. Replies
    11
    Views
    1,140

    Kevin is a great guy! If you ever get the chance...

    Kevin is a great guy! If you ever get the chance to attend his tech day, don't miss it.
  24. Replies
    23
    Views
    2,552

    I am in the midst of a similar project with my...

    I am in the midst of a similar project with my son. We will be moving at a much slower pace, so I will watch and learn as you go through the process!

    :lurk
  25. Replies
    15
    Views
    2,479

    :scratch I wonder what made them think they have...

    :scratch I wonder what made them think they have the right to "forbid" the use of a sidecar? Perhaps some governments grant the manufacturer that power.
Results 1 to 25 of 1194
Page 1 of 48 1 2 3 4