Search:

Type: Posts; User: ba-heed; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.10 seconds.

  1. Replies
    0
    Views
    307

    tank for R100 RT

    Hi, I am going for the basic look and lighter bike on my 1980 R100RT
    I would like to fit a smaller gas tank
    can anybody tell me what airhead model fuel tanks will fit?
    Much obliged for any help...
  2. Replies
    7
    Views
    698

    water in gear oil!

    Hello to all , I had a nasty moment when checking oil levels today .
    When I removed the gear-oil filler a white cream came pouring out , way over level and emulsified ,
    must be water I guess ,...
  3. Replies
    3
    Views
    522

    synchronizing carbs

    Good Day , I am synching the Bings on my 1980 R100RT.
    Using my new 'TwinMax' balancer
    all is going well, I went carefully through the Snobum procedure and I have the engine idling nicely at around...
  4. Thread: 2nd gear

    by ba-heed
    Replies
    1
    Views
    256

    2nd gear

    Good Morning all, Quick question, I have a noisy second gear ( 1980 R100RT 85K )
    clunk , clunk and a shaft running noise.
    Its only in second. First is fine and as soon as I get up into third she...
  5. Replies
    14
    Views
    1,755

    synchronizing Bing carbs

    Hello , I have just rebuilt the Bing 94 Carbs on my 1980 R100RT , I changed the cables also and the bike starts and runs but has a noticeable vibration.
    so now I want to adjust the synch. of the...
  6. Replies
    1
    Views
    301

    electrical problem

    Hi everybody, i need a little help with an electrical issue. I have a 1980 R100RT that I recently purchased In a very well used condition, and the last few weeks I have been pulling it apart and...
  7. Replies
    2
    Views
    344

    R100RT brake relocation

    Thank you Bruce
  8. Replies
    2
    Views
    344

    R100RT front brake re-location

    Greetings all round, I have a quick question, as part of the restoration process I am relocating the front brake reservoir on my 1980 R100RT from under the tank to the handlebars. please see the...
  9. Thread: Fork oil

    by ba-heed
    Replies
    19
    Views
    1,496

    Fork oil

    Hello all round, I would like to change my fork oil on my 1980 R100RT. After checking the specs I have looked for Aeroshell 4 but can only buy a case, so Plan B what else shall I use? all advice...
  10. Thread: Oak's Manual

    by ba-heed
    Replies
    8
    Views
    1,331

    Oaks Manual

    Thanks M_stock, No I meant the "Oak's top end manual" in particular, a different publication. However these Chi-Tech books are new to me and are a 'must have'
    Thank you very much , Steve the Heed
  11. Replies
    8
    Views
    1,429

    bing carb rebuild

    Krpntr, I am going to send you a stamped addressed envelope and the cost of the part just for the provenance of the clip and to prove that you kept it for a reason.
    Please take pleasure in the fact...
  12. Replies
    8
    Views
    1,429

    Bing Carb rebuild

    Hi, I am rebuilding the Bings on my 1980 R100RT. All going well so far with the rebuild kit from Bing, then I found that on one carb that tiny hair spring clip that holds the float needle to the...
  13. Thread: Oak's Manual

    by ba-heed
    Replies
    8
    Views
    1,331

    Oak's Manual

    Thanks Kurt
  14. Thread: Oak's Manual

    by ba-heed
    Replies
    8
    Views
    1,331

    Oak's Manual

    Hi can somebody please tell me me where I can buy an Oak's manual? Thanks and regards all round , Heed
  15. Replies
    5
    Views
    432

    40mm Bing Carb rubbers

    OK I found them on bike bandit, thanks y'all. Thanks esp. for the links page Lew, All the best, ride safe, Steve.
  16. Replies
    5
    Views
    432

    40mm carb. rubbers

    Yes Lew, thanks mate , thats exactly what I mean, I need four of 'em
  17. Replies
    5
    Views
    432

    40mm Bing carb rubbers

    Good day everybody, I am rebuilding the Bings and I need the rubber boot connections top and bottom , esp. the ones to the head are cracked and split , I cannot seem to find them online , has anybody...
  18. Replies
    13
    Views
    615

    Tank repair exposed

    I had the fuel tank sandblasted today and I think the repair would be more costly than a good used tank so I am shopping.
  19. Replies
    13
    Views
    615

    r100rt restoration

    Thanks Jeff I will check the prices. Thanks for the Tank info James that all makes sense. Plus I will take it easy with the torque wrench, did you have to re-weld the block on your '88 or can you fit...
  20. Replies
    13
    Views
    615

    R100 restoration

    Thanks Meister, thanks Fish, Good idea on the forward brake reservoir get it out from under the tank.
    I attach a shot of the tank repair I am going to get it sandblasted to see just what I have got...
  21. Replies
    13
    Views
    615

    R100rt

    Hey Kent, look at that handlebar mount and tell me what you think , that is some kind of "set back" deal am I right?
  22. Replies
    13
    Views
    615

    R100rt

    Thanks Kent, for some reason I thought that odd shaped headlight bucket was particular to the fairing assembly. I have the "ears" I will re-think now and look closer at the light. I have a bunch of...
  23. Replies
    13
    Views
    615

    restoration other side on

    Heres the other side
  24. Replies
    13
    Views
    615

    R100RT restoration project begins

    Ok here is my new 1980 R100RT, I have just removed the fairing to see what I am up against. It will not go back I am going for the basic bike. A good gunk and de-grease first right?
    I can see that...
  25. Thread: 1980 r100rt

    by ba-heed
    Replies
    9
    Views
    1,032

    Thanks

    I greatly appreciate this input. The bike has not arrived yet from Chicago, Shipper due in a week or so.
    To Subagon, thank you, I am indeed in Florida I live in Fort Lauderdale,
    I don't think I...
Results 1 to 25 of 27
Page 1 of 2 1 2