Search:

Type: Posts; User: mhuf; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    9
    Views
    453

    Thanks for the effort! Anton and GSAddict...

    Thanks for the effort!

    Anton and GSAddict were spot on.... as usual.
  2. Replies
    9
    Views
    453

    Thanks Anton. I have not yet installed the final...

    Thanks Anton. I have not yet installed the final drive so should be easy.
  3. Replies
    9
    Views
    453

    Anton, I was not inside the tranny. Had the...

    Anton, I was not inside the tranny. Had the dealer put in a new input shaft. I was thinking that maybe these are to go where the shock meets the swing arm or stabilizer possibly? Can't find them in...
  4. Replies
    9
    Views
    453

    R1150RT Black Plastic Washers

    Can anyone tell me where I should have put these black plastic washers/spacers while re-installing the transmission?
  5. Replies
    252
    Views
    30,602

    He's a regular contributor here and over on...

    He's a regular contributor here and over on advrider forum and I think he's maintaining a list for new orders there.
  6. Replies
    252
    Views
    30,602

    Modified Clutch

    Just wanted to show a couple photo's of the modified clutch with the spacer kits acquired from cele0001. I had a local machine shop remove rivets from clutch plate and install spacer with new rivets...
  7. Replies
    21
    Views
    2,890

    anybody find a good source for the black zip ties...

    anybody find a good source for the black zip ties for boot re-closure?
  8. Replies
    252
    Views
    30,602

    understandable, BC has some of the most beautiful...

    understandable, BC has some of the most beautiful country on the planet.
  9. Replies
    252
    Views
    30,602

    Thanks for all your advice. Very much...

    Thanks for all your advice. Very much appreciated. I'm going to replace the clutch plate and get some emery disks for my orbital!
  10. Replies
    252
    Views
    30,602

    Thanks GSAddict. Sliding meaning either...

    Thanks GSAddict. Sliding meaning either incomplete engagement or disengagement of the clutch for extended periods?

    Is the outside to interior wear pattern normal? Would you recommend replacing...
  11. Replies
    252
    Views
    30,602

    Is this wear(worn circle center frame) on the...

    Is this wear(worn circle center frame) on the outside of the clutch housing cover normal?
    44353
  12. Replies
    252
    Views
    30,602

    Neil, I can't tell if it's warped. There is...

    Neil, I can't tell if it's warped. There is definitely a pattern of wear from outside to in (see photos) There also does appear to be a slight depression in the black area and also the metal feels...
  13. Replies
    252
    Views
    30,602

    nothing remarkable, in my opinion, on the...

    nothing remarkable, in my opinion, on the corresponding wearing surfaces of the clutch plate
  14. Replies
    252
    Views
    30,602

    That's my concern...any thoughts Roger?

    That's my concern...any thoughts Roger?
  15. Replies
    252
    Views
    30,602

    Can anyone offer opinion as to the cause of the...

    Can anyone offer opinion as to the cause of the black scoring on my R1150RT housing cover? This bike did have input shaft and clutch hub failure. Could this be further evidence of misalignment? I'm...
  16. Replies
    252
    Views
    30,602

    Dealership called late yesterday and said my...

    Dealership called late yesterday and said my "transmission is repaired and the procedure went very well" (sounds like the patient survived). New input shaft, seals and front and rear bearings.
    ...
  17. Replies
    252
    Views
    30,602

    of course, will do!

    of course, will do!
  18. Replies
    252
    Views
    30,602

    The decisions have been very difficult when deep...

    The decisions have been very difficult when deep pockets aren't an option. I think Esmir and Bruno have viable solutions options, albeit Bruno's $500-600 option is expensive and Cele001's is much...
  19. Replies
    252
    Views
    30,602

    [QUOTE=nrpetersen;928505] I have the...

    I have the transmission out of the bike and currently in the hands of a Central PA BMW dealer. They are going to replace the input shaft, seals and front and rear bearings. When I reassemble I plan...
  20. Replies
    252
    Views
    30,602

    [QUOTE=roger 04 rt;928470]I agree that would...

    [QUOTE=roger 04 rt;928470]I agree that would measure shaft centerline errors directly but he would need to have your rig and the front half of the transmission case. I wonder if there is any chance...
  21. Replies
    252
    Views
    30,602

    [QUOTE=roger 04 rt;928300]When you posted I was...

    [QUOTE=roger 04 rt;928300]When you posted I was writing the response below. Is there any chance you could have them measure the flywheel/clutch housing (I don't know the correct term)...
  22. Replies
    252
    Views
    30,602

    I took my 04RT transmission to the dealer last...

    I took my 04RT transmission to the dealer last week for an input shaft replacement. I'm hoping, once back together with a new clutch plate, I can get many more miles out of this 38k mile bike. One...
  23. Replies
    252
    Views
    30,602

    just going with the modified clutch hub

    just going with the modified clutch hub
  24. Replies
    252
    Views
    30,602

    cele0001 (Esmir), I'm on a waiting list for one...

    cele0001 (Esmir), I'm on a waiting list for one of the modified clutch hubs. I think this is the route I'm going to take. Seems to me a good compromise when considering the condition of my splines....
  25. Replies
    252
    Views
    30,602

    OK thanks GSAaddict. Is that the Optimol T White...

    OK thanks GSAaddict. Is that the Optimol T White Paste in your syringe?
Results 1 to 25 of 77
Page 1 of 4 1 2 3 4