Search:

Type: Posts; User: bmweuro; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    6
    Views
    701

    I just did rod bearings and small end bushings as...

    I just did rod bearings and small end bushings as well I have adjusted the custom timing chain tensioner in and out to see if the tone of the sound changes with no luck.
  2. Replies
    6
    Views
    701

    Any idea's?

    Any idea's?
  3. Replies
    4
    Views
    393

    ..and the RS springs are stiffer.

    ..and the RS springs are stiffer.
  4. I'm running a 135/15 car tire on the rear of my...

    I'm running a 135/15 car tire on the rear of my BMW rig and and 125/15 on the sidecar. They last a long time.
  5. Replies
    6
    Views
    701

    Engine knock at low RPM

    I have a 76 R90 motor that has new rod bearing and the small end bushings have been replaced and sized to the wrist pins. The motor has 40mm Bings with 170 main jets, 45 idle' 2.68 needle jets and...
  6. Replies
    166
    Views
    45,948

    Sticky: My shop truck 40186 40187

    My shop truck

    40186

    40187
  7. Replies
    30
    Views
    1,421

    If you use anything other than a soft plastic...

    If you use anything other than a soft plastic bristle brush you will remove the plating. The Eagle One works great and for the price and how much you use it's worth it. I also use it on the engine...
  8. Replies
    4
    Views
    627

    All 70-84 front cross over pipes are 100% the...

    All 70-84 front cross over pipes are 100% the same minus the R65 range. They are 38mm in diameter which is very close to 1.5".
  9. Replies
    30
    Views
    1,421

    1. Take all of your original hardware and...

    1. Take all of your original hardware and degrease it. Do not use a wire brush.
    2. In small batches in a small plastic container spray the hardware with Eagle One mag wheel cleaner for chrome...
  10. Replies
    5
    Views
    399

    The springs over the damping rods are old...

    The springs over the damping rods are old Luftmiester anti dive springs. After 1980 BMW did not put a bumper in the bottom of the fork. By new factory BMW fork springs if your bike has over 50k...
  11. Replies
    6
    Views
    314

    There is not. I would cut an inch out and weld it...

    There is not. I would cut an inch out and weld it back up. The other option is make a fold out handle so you have more leverage to pull up with.
  12. Replies
    9
    Views
    574

    I have lowered a lot of BMW's over the years for...

    I have lowered a lot of BMW's over the years for customers that are vertically challenged. San Jose BMW made a few alloy upper triple clamps that allowed you to move the fork tubes up, throw away the...
  13. I think the R50/5 is a wonderful machine.

    I think the R50/5 is a wonderful machine.
  14. Replies
    24
    Views
    1,341

    /5 mufflers will fit all /6 and /7 models through...

    /5 mufflers will fit all /6 and /7 models through 1984.
  15. Replies
    8
    Views
    714

    Make sure when you're reassembling to lock tite...

    Make sure when you're reassembling to lock tite the upper eyelet to the shaft or it will unscrew itself.
  16. Replies
    2
    Views
    605

    It's the best bang for the buck.

    It's the best bang for the buck.
  17. Replies
    9
    Views
    976

    The easiest fix is to pull the right cylinder off...

    The easiest fix is to pull the right cylinder off which is closest to the thrust washer and try and work it back on.
  18. Thread: R100c ?

    by bmweuro
    Replies
    7
    Views
    794

    +1

    +1
  19. Replies
    7
    Views
    1,153

    The interesting thing about the recall is there...

    The interesting thing about the recall is there was only one wheel failure ever recorder by BMW. I know a lot of people that still run the early wheel. If you are concerned take the wheel off and set...
  20. Thread: R100c ?

    by bmweuro
    Replies
    7
    Views
    794

    The R100CS was from 81-82. If it is has dual disc...

    The R100CS was from 81-82. If it is has dual disc from the factory then it was more than likely an R100S. Check the VIN?
  21. Replies
    6
    Views
    664

    Adjust the cable up at the handlebars until the...

    Adjust the cable up at the handlebars until the arm at the back of the transmission is parallel to the back cover. Adjust the free play at the throw out bearing arm until you have 3-4mm at the...
  22. Replies
    5
    Views
    515

    Theo speaks Engish. Just send him an email and...

    Theo speaks Engish. Just send him an email and tell him what you are after.
  23. Replies
    20
    Views
    2,660

    There is a steel line underneath the fender...

    There is a steel line underneath the fender connecting both calipers and one rubber line on one caliper and a bleed screw on the other caliper. It work very well. If you are trying to piece something...
  24. Thread: /2 conversion

    by bmweuro
    Replies
    12
    Views
    2,461

    I know this is an old thread but is there any...

    I know this is an old thread but is there any updated info on the swing arm mod to a later rear drive?
  25. You can use the following tanks 85-87 R65 85-87...

    You can use the following tanks
    85-87 R65
    85-87 R80
    85-87 R80RT
    85-92 R100RS
    85-95 R100RT
Results 1 to 25 of 260
Page 1 of 11 1 2 3 4