Search:

Type: Posts; User: 148491; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.07 seconds.

  1. Replies
    2
    Views
    366

    Yep, that's my plan thanks. I'll have a boo...

    Yep, that's my plan thanks. I'll have a boo under that cover after I've installed the new combo switch.
  2. Replies
    20
    Views
    1,370

    I just put a new fuel filter in my 1150...

    I just put a new fuel filter in my 1150 yesterday. I had changed the OEM at 45.5K miles with a Mann MKW44 from the Boneyard. Couldn't wait for one from them so after reading many threads I put in a...
  3. I've been using my home made manometer for years...

    I've been using my home made manometer for years for my airheads and my 1150GSA. It's been a good soldier and cost under $10 to make. I have to say that recently I've been looking at the Harmonizer...
  4. Replies
    10
    Views
    528

    Solved!

    Well I went out the shop first thing and took the throttle cable off the throttle body and carefully re-installed it. The cable was feeding onto the pulley but it's possible the underside cabling...
  5. Replies
    10
    Views
    528

    Paul:

    Thanks....I assume the bell crank end is in the bowden box under the abs etc?

    I just finished disconnecting the left cable and then carefully reconnecting it again. I also re did the voltage on...
  6. Replies
    10
    Views
    528

    Morning Roger....I will re measure the voltage on...

    Morning Roger....I will re measure the voltage on the TPS this morning but first I will revisit the left hand cable. It is strange that it's pretty much screwed all the way down and even then not...
  7. Replies
    10
    Views
    528

    Follow up

    Everything was fine prior to me putting the bodies back on etc with no change to the CCP etc. I've been reading for hours now and what I'm coming back to is "do I have slack in the throttle cables?"...
  8. Replies
    10
    Views
    528

    Thanks Roger. Yes it was Fuse #5 and the battery...

    Thanks Roger. Yes it was Fuse #5 and the battery had also been disconnected the night before. The fast idle lever was down when the throttle was opened. The cables are also seated correctly in the...
  9. Replies
    10
    Views
    528

    Low RPM Stall/Stutter after TPS reset

    '02 1150GSA

    Just installed Dan Cata's Throttle Body Kits (both). I positioned the TPS as closely as I could to the pre-rebuild spot. After getting an initial 1.06v reading and fiddled around until...
  10. Replies
    4
    Views
    512

    That did the trick Paul....I think when it comes...

    That did the trick Paul....I think when it comes time for a clutch I'll look into a stainless clutch line from Spiegler or some place to replace the OEM as there some signs of the typical corrosion...
  11. Replies
    4
    Views
    512

    Thank you Doctor Paul! I'll bleed it again in...

    Thank you Doctor Paul! I'll bleed it again in the morning...it's a tad easier bleeding with a speed bleeder attached now. :)
  12. Replies
    4
    Views
    512

    Clutch Slave Replacement 1150GS

    I just replaced my clutch slave on an 02 1150 GSA with 93K miles. Everything went okay and appears to work ok however the clutch seems to engage a little sooner on the lever than before.

    Is...
  13. Replies
    8
    Views
    464

    Sent you a PM

    Sent you a PM
  14. Replies
    8
    Views
    464

    Yes it would.....

    Yes it would.....
  15. Replies
    8
    Views
    464

    1150 Gas Cap Replacement

    After breaking the hinge on my gas cap I've elected to go on Beemer Boneyard's waiting list for a used one which could take some time. Duct tape is working for now...

    In the meantime, has anyone...
  16. Replies
    6
    Views
    607

    Thanks for the input! I don't mind replacing all...

    Thanks for the input! I don't mind replacing all it's just a question of what is all?

    There's a bunch of parts in the clutch assembly front to back in the parts fiche....so the wearing parts are...
  17. Replies
    6
    Views
    607

    Which Clutch Parts?

    My '02 GSA is showing no signs, at this point, of needing a new clutch at 92K miles however it's closer to the end of it's life than the beginning.

    Is it subjective which of the parts to replace? ...
  18. Thread: FD Time

    by 148491
    Replies
    23
    Views
    2,713

    +1 what the other guys have said. I'm at 89K,...

    +1 what the other guys have said. I'm at 89K, original FD, and see a bit of that smudge every time and that's with changing my fluid every 6k or so as well.
  19. Replies
    11
    Views
    1,243

    Can you elaborate on how to make your own reader?

    Can you elaborate on how to make your own reader?
  20. Thread: Horns

    by 148491
    Replies
    10
    Views
    1,014

    Stebel Nautilus

    I was very satisfied with the Stebel. It did pack it in after 3 years, likely from a combination of dust, washboard etc, however I recently replaced it with a clone from Korea for 28 bux delivered. ...
  21. Thread: ABM Peak Rotor

    by 148491
    Replies
    3
    Views
    546

    Thanks guys...

    Thanks guys...
  22. Thread: ABM Peak Rotor

    by 148491
    Replies
    3
    Views
    546

    ABM Peak Rotor

    Anyone have one of these from BeemerBoneyard? Stainless Steel and German made....

    Looking for feedback :dunno
  23. Replies
    21
    Views
    1,415

    +1 for Pledge

    My plastic's been huffing that stuff for years.... :thumb

    Costco is now stocking oversized two packs....lol
  24. Replies
    6
    Views
    540

    Solved!

    After going back to womb with this issue and under the strict supervision of GS Addict the problem has been solved.

    Stuck/faulty front brake micro switch. Working now but new switch to be...
  25. Replies
    6
    Views
    540

    LOL, thanks but he's already on it! :brow

    LOL, thanks but he's already on it! :brow
Results 1 to 25 of 71
Page 1 of 3 1 2 3