Search:

Type: Posts; User: GSAddict; Keyword(s):

Page 1 of 51 1 2 3 4

Search: Search took 0.16 seconds.

  1. Actually all you need is a 5/16" x 2" (or so)...

    Actually all you need is a 5/16" x 2" (or so) bolt and insert thru flywheel hole and into engine case, as you would in locating TDC. Transmission case not req'd
  2. Replies
    5
    Views
    144

    Do you have the original rubber brake lines? ...

    Do you have the original rubber brake lines?

    If so I would suspect a blockage on the return of fluid.
    Replace with SS Teflon and flush thoroughly.

    Lots of issues with debris I've seen.
  3. Replies
    8
    Views
    457

    Brain fart, I missed that, came in the thead...

    Brain fart, I missed that, came in the thead late.
    Probably a pinched wire
  4. Replies
    8
    Views
    457

    On the 1100's the neutral switch is on the the...

    On the 1100's the neutral switch is on the the back of the gear position switch. (5 speeds)
    On the 1150's it's all done in one switch (6 speeds)
  5. Replies
    11
    Views
    346

    My fix for the R1150GS

    Infinitely adjustable for any load/shock height

    http://i583.photobucket.com/albums/ss275/GSAddict/IMGP0593_resize.jpg
  6. If it's that dead nothing is going to revive it....

    If it's that dead nothing is going to revive it.
    Replace the battery.
    It's not that difficult to do.
  7. Replies
    8
    Views
    403

    Never heard that term up here. Thanks. sounds...

    Never heard that term up here. Thanks.
    sounds like a possible grounding issue
  8. Let alone hold a charge..........

    Let alone hold a charge..........
  9. Replies
    8
    Views
    403

    What is a tag lt bulb?

    What is a tag lt bulb?
  10. Check it once more using the 1mm solder method....

    Check it once more using the 1mm solder method.
    Just about every one I have done has had excessive preload.

    Some interesting reading recently...
  11. How it's installed

    Insert locating plate (5) into brake caliper.
    Note:
    The installed position must be correct (arrow point-
    ing in forward-travel direction).


    .
  12. Great photo shoot, a good resource for the...

    Great photo shoot, a good resource for the members.
  13. BE CAREFUL - that ADV .pdf shows the bracket...

    BE CAREFUL - that ADV .pdf shows the bracket installed backwards !!!
    I notified them but they have not fixed as of yet.

    This link shows the bracket the right way around....
  14. Thanks Doug, Keep up the good work, donation sent.

    Thanks Doug, Keep up the good work, donation sent.
  15. Replies
    12
    Views
    458

    Agreed

    Agreed
  16. Replies
    12
    Views
    458

    I wonder if it could be this ball (9) 7 11 9 986...

    I wonder if it could be this ball (9)
    7 11 9 986 270 BALL - 6MM III

    From the Max fiche R1100R
  17. Replies
    12
    Views
    458

    You dodged a bullet.

    You dodged a bullet.
  18. I just traced the bearing back to the...

    I just traced the bearing back to the manufacturer (INA) I was told that it was made for the manufacturer only (Magura)

    In all the units I have changed, by the time the bearing had failed, the...
  19. Start at the auto parts stores, the piggyback...

    Start at the auto parts stores, the piggyback will to be very narrow as the fuses are very close together.
    If you strike out, PM me I can make something up for you and mail.
  20. Only problem with wiring direct is one must...

    Only problem with wiring direct is one must remember to turn the seat off when leaving the bike or a flat battery will be waiting upon your return.
    A switched positive is more desirable.
    Using a...
  21. The best is to run it right back to Battery -. ...

    The best is to run it right back to Battery -.

    Tying to one of the Brown wires (BMW's negative colour) could cause issues depending on it's circuit loads.
  22. GM Weather Pack Terminals

    Methinks this will help you.

    http://www.amazon.com/Delphi-Packard-Weatherpack-Terminal-16-14/dp/B004DVM7RG
    http://www.hipoparts.com/weather-pack-2-pin-sealed-wiring-connector-kit/...
  23. Reviving this thread: THIS IS WHY - the...

    Reviving this thread:

    THIS IS WHY - the bearings are not "sealed" as we know it.
    Thanks to an inmate on ADV.
    See post #27
    http://www.advrider.com/forums/showthread.php?p=24410418#post24410418
    ...
  24. Replies
    69
    Views
    2,985

    Check your PM's

    Check your PM's
  25. Replies
    69
    Views
    2,985

    You said your spacer measured 2.37mm The quote...

    You said your spacer measured 2.37mm

    The quote below is from the BMW OE factory manual.

    " Place original spacer (1) or spacer measuring
    2.25 mm (0.0886 in) in thickness on crown wheel
    (for...
Results 1 to 25 of 1274
Page 1 of 51 1 2 3 4