Search:

Type: Posts; User: PAS; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.08 seconds.

  1. Years ago I added one to the headlight shell on...

    Years ago I added one to the headlight shell on my 81 R100RT. It and the head light are switched thru a marine rocker switch on the dash.
    I wanted to be able to turn the head light off and just...
  2. Replies
    5
    Views
    301

    Lets back up a minute. There are two torque...

    Lets back up a minute. There are two torque values listed in my Chiltons for my 1150RT
    Mounting bracket bolts 21Nm 15' lbs.
    Pivot bolt 42Nm 31' lbs

    OTHER bikes list the higher torque ...
  3. Replies
    35
    Views
    1,279

    Well done on the scam!!!

    Well done on the scam!!!
  4. Replies
    16
    Views
    682

    I have to agree!

    I have to agree!
  5. Replies
    15
    Views
    857

    My 03 R1150RT did the same thing until I replaced...

    My 03 R1150RT did the same thing until I replaced the battery.
  6. Thread: Oilhead Newbie

    by PAS
    Replies
    17
    Views
    1,547

    Sounds like the clutch slave or shaft seal leaked...

    Sounds like the clutch slave or shaft seal leaked and ruined the clutch plate. Beemerboneyard is a great place to buy parts and they give MOA members a discount. A happy customer and not related...
  7. Thread: Oilhead Newbie

    by PAS
    Replies
    17
    Views
    1,547

    As far as the quick disconnects, I was told by...

    As far as the quick disconnects, I was told by Ted porter at the Beemershop that only the male end breaks. I only replaced the male ends. One could be metal and one could be plastic in that case.
  8. Replies
    14
    Views
    487

    There should be a type of hook on the inside...

    There should be a type of hook on the inside front of each side cover and there are a pair of black rubber bands that stretch across the front of the battery to hold them on. They look like big...
  9. Thread: Oilhead Newbie

    by PAS
    Replies
    17
    Views
    1,547

    I have both, an 81 R100RT and an 03 R1150RT. Be...

    I have both, an 81 R100RT and an 03 R1150RT. Be very careful of the power brakes at slow, parking lot speed. Especially when turning and riding two up. I try and use one finger on the front brake...
  10. Replies
    7
    Views
    561

    I dont know about the fairing but the bags are...

    I dont know about the fairing but the bags are the same as my 81's and I dont think the smoke red was available that year. I'm thinking it was around 78 for that color. The only fairing changes were...
  11. Replies
    7
    Views
    616

    I had somewhat of a similar problem on my 03 RT. ...

    I had somewhat of a similar problem on my 03 RT. It turned out the left turn signal switch button was sticking. I used WD-40 to spray it. I bought some Deoxit to try when the weather warms up.
    ...
  12. Thread: Water in the Carbs

    by PAS
    Replies
    47
    Views
    2,125

    Pilots reading this post should relate to the...

    Pilots reading this post should relate to the "carb heat knob" on some old aircraft.
  13. The original poster hasnt been heard from since.

    The original poster hasnt been heard from since.
  14. Thread: tranny input shaft

    by PAS
    Replies
    248
    Views
    13,403

    Must be a common characteristic of red grease!...

    Must be a common characteristic of red grease!
    43668
  15. Replies
    26
    Views
    2,798

    I'm buying! Thats the best I can do.

    I'm buying! Thats the best I can do.
  16. 48214 a private message has been sent to you.

    48214 a private message has been sent to you.
  17. Replies
    9
    Views
    737

    Totally Agree!

    Totally Agree!
  18. Replies
    11
    Views
    751

    I recently replaced my pivot bearings with OEM's...

    I recently replaced my pivot bearings with OEM's due to a couple missing needles (used bike). I have read good and bad about the bushing kits so I went with stock. The Beemer Shop no longer sells...
  19. Replies
    9
    Views
    721

    I solvent cleaned mine then scuffed up lightly...

    I solvent cleaned mine then scuffed up lightly then sprayed with Duplicolor silver metallic then a light coat of clear. They look great!
    81 R100RT
  20. Replies
    22
    Views
    2,316

    Isnt that the truth! All the tupperware...

    Isnt that the truth! All the tupperware fasteners on my 03 RT are stainless that have been either painted or coated black by BMW.
  21. Replies
    21
    Views
    1,095

    Thanks for posting the article and its sad to...

    Thanks for posting the article and its sad to hear he has passed. He and the bike stood out in the crowd, I wish I had met him. I just found this picture.
    42969
  22. Replies
    21
    Views
    1,095

    I believe that bike showed up at the Finger...

    I believe that bike showed up at the Finger Lakes Rally in the past (Watkins Glen, N.Y.) Even had the net on the front.
  23. Replies
    175
    Views
    9,992

    Very interesting discussion. Good info here:...

    Very interesting discussion. Good info here: http://www.rbracing-rsr.com/bmw_clutches.html
  24. Replies
    65
    Views
    6,714

    Did you contact the seller? Getting into the...

    Did you contact the seller? Getting into the clutch-input spline is doable but I wouldnt call it easy, very time consuming. I'm a bit surprised that most dont think the seller should be involved...
  25. Replies
    65
    Views
    6,714

    Sorry to hear about this. If the seller was any...

    Sorry to hear about this. If the seller was any kind of good guy he would take care of a refund of sorts. I believe there is a law about new purchases like this. Sounds fishy to me.
Results 1 to 25 of 360
Page 1 of 15 1 2 3 4