Search:

Type: Posts; User: wjg4oh; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.05 seconds.

  1. Replies
    40
    Views
    4,377

    Very informative write-up, racer7. Thanks! I'm...

    Very informative write-up, racer7. Thanks!

    I'm interested to hear about your experience with the AF-XiED. I just installed one on my F800GT last week. After running a tank full of gas through it...
  2. Replies
    291
    Views
    73,707

    I have had the LC-1 on my 2001 R1150GS for a few...

    I have had the LC-1 on my 2001 R1150GS for a few months now with good results -- increased torque, improved driveability, and improved mileage in the range of 2-3 mpg.

    My 2003 K1200GT (brick...
  3. Replies
    291
    Views
    73,707

    I had a chance to get out yesterday afternoon for...

    I had a chance to get out yesterday afternoon for a brief ride on the Interstate where I could get the bike into the upper gears. In 4th, 5th and 6th above 4000 rpm the AFR never got above 13.8,...
  4. Replies
    291
    Views
    73,707

    Roger, I was away for a few days but now back...

    Roger, I was away for a few days but now back home, and as soon as the weather clears I'll get out for more runs and will log data using LogWorks3.

    By "small-TPS-angle" do you mean small...
  5. Replies
    291
    Views
    73,707

    Roger and others... I noticed something...

    Roger and others...

    I noticed something interesting on my LC-1 equipped 2001 R1150GS. I have Lambda set at .94 (13.8:1 AFR). As long as I ride below 4000 rpms the engine hovers right around 13.8...
  6. Replies
    291
    Views
    73,707

    Update on the LC-1 on my 2001 R1150 GS: The...

    Update on the LC-1 on my 2001 R1150 GS:

    The fuel injectors I had sent off for cleaning (RC Engineering) came back today. The report showed they had flow rates of 315 and 294 cc/min before...
  7. Replies
    291
    Views
    73,707

    I had been using Bosch 4417's, but put in...

    I had been using Bosch 4417's, but put in Autolite 3923's before going for a nice ride yesterday afternoon. I also put some Techron in the tank. Instead of focusing on how the engine was running I...
  8. Replies
    291
    Views
    73,707

    I took advantage of our 60 degree weather in NE...

    I took advantage of our 60 degree weather in NE Ohio today and took the GS out for the afternoon to experiment with different lambdas.

    Taking Roger's advice I first programmed the LC-1 to lambda =...
  9. Replies
    291
    Views
    73,707

    It warmed uo to 40 degrees today so I reset the...

    It warmed uo to 40 degrees today so I reset the Motronic, programmed the LC-1 to lambda 1.01, turned on the "choke", started the bike and let it warm up. I have the 3.5 bar fuel regulator installed,...
  10. Replies
    291
    Views
    73,707

    IÔÇÖve been following roger04rtÔÇÖs posts...

    IÔÇÖve been following roger04rtÔÇÖs posts on enriching oilhead fueling using the LC-1 by Innovate Motorsports, and I finally installed one on my 2001 R1150GS (72,000 miles). I also installed a...
  11. Replies
    23
    Views
    2,744

    Lee, I've already replaced the o-rings, and the...

    Lee, I've already replaced the o-rings, and the caps fit tightly.

    When the manifolds go is it the rubber boot or the hard part that bolts to the head (warped). Any possibility they can be...
  12. Replies
    23
    Views
    2,744

    Just ordered a MotionPro. Thanks for the link,...

    Just ordered a MotionPro. Thanks for the link, 98lee.

    It looks like I have a vacuum leak at the throttle bodies. I'm going to do more diagnosis, but it appears to be those $50 intake manifolds...
  13. Replies
    23
    Views
    2,744

    Looks like I may hold the record for *most* shims...

    Looks like I may hold the record for *most* shims -- 2 in 22,000 miles!

    After the valve adjust, the air bypass screw on #1 needs two more turns than the ones on #2 and #3, which are nicely...
  14. Replies
    23
    Views
    2,744

    Thanks for the suggestions, 98lee. I measured...

    Thanks for the suggestions, 98lee.

    I measured the valve clearances very carefully this afternoon (third time!) using the go-no-go technique and this is what I found:

    #1 .356mm, .014"
    #2 ...
  15. Replies
    23
    Views
    2,744

    I bought the bike at 10,000 miles. I suppose the...

    I bought the bike at 10,000 miles. I suppose the PO could have adjusted the valves, but I rather doubt it.

    I try to be careful not to use too much force on the feeler gauges -- when I feel a...
  16. Replies
    23
    Views
    2,744

    1994 K75 valve adjust needed?

    My '94 K75 has 22,000 miles on it. I checked the valves for the first time last week and the intake valves were all nicely within spec, but all three exhaust valves were over .30 mm. I was surprised...
  17. Replies
    291
    Views
    73,707

    Am I understanding this correctly -- that...

    Am I understanding this correctly -- that increasing the fuel pressure takes the place of both the Booster Plug and Wideband O2 sensor/adjustment? Very interesting thread, Roger.
  18. Replies
    291
    Views
    73,707

    Roger, I really appreciate your generosity in...

    Roger, I really appreciate your generosity in sharing your data on the forum. It sheds a lot of light on an area about which there is much conflicting information. Your data and explanations are...
  19. Replies
    16
    Views
    1,348

    I got a 2" x 2" square sample of Corian for free...

    I got a 2" x 2" square sample of Corian for free at Home Depot. You can pick your color, too.
  20. Replies
    2
    Views
    747

    Holt BMW (http://www.holtbmw.com/) in Athens,...

    Holt BMW in Athens, Ohio is a Glasurit dealer and was able to supply a color for me that was not otherwise available.
  21. Replies
    13
    Views
    2,029

    Put the seat in the first position at the rear...

    Put the seat in the first position at the rear latch, lift the front of the seat up as far as it will go and slide the seat forward until it latches in the second position at the rear. Very easy to...
  22. Replies
    8
    Views
    880

    Michelin's U.S. website shows the Activ in sizes...

    Michelin's U.S. website shows the Activ in sizes that fit the K75: 100/90-18 front and 130/90-16 rear. I will probably put them on when my Macadam 50's wear out.

    Wally
    Shaker Heights, OH
    1994...
  23. Replies
    21
    Views
    2,721

    Dean, I was responding to the first poster in the...

    Dean, I was responding to the first poster in the thread who has the same fairing as mine. Your's is the Rifle Sport fairing. My first K75 had the Sport on it, and you're right that it attaches...
  24. Replies
    21
    Views
    2,721

    The struts - a short female end, and a long male...

    The struts - a short female end, and a long male end which I had to shorten a bit. I found the rubber cushioned clamps on the Internet at a very reasonable cost.
  25. Replies
    21
    Views
    2,721

    Side view of Rifle Superbike showing cutout to...

    Side view of Rifle Superbike showing cutout to accommodate turn signals. I wouldn't have had to take off quite so much.
Results 1 to 25 of 29
Page 1 of 2 1 2