Search:

Type: Posts; User: DennisDarrow; Keyword(s):

Page 1 of 45 1 2 3 4

Search: Search took 0.08 seconds.

  1. So didja get it...

    So didja get it started..............???????????????
  2. Replies
    10
    Views
    412

    Thoughts on: After one drills a hole, perhaps 1/2...

    Thoughts on: After one drills a hole, perhaps 1/2 the diameter of the threaded/shank portion of the fastener and finds the highest quality of EZ out available, what are thoughts about using an air...
  3. Replies
    10
    Views
    412

    How much torque do you figure one of these will...

    How much torque do you figure one of these will hold up to, Paul. I have a 6mm or so, the threaded portion of the bolt is 6 mm, allen head bolt, , that the head is stripped out, very similar to this...
  4. Goooood thought.......Start there and then your...

    Goooood thought.......Start there and then your spark..........Good luck.....God bless........Dennis
  5. :dunno Surely not to argue or get into grief...

    :dunno Surely not to argue or get into grief here but:

    Was having a senior moment here about all this needle business. For some reason had it in my head that it was the second notch on an...
  6. Replies
    36
    Views
    1,541

    For me, it's just the same as Jimmy describes. ...

    For me, it's just the same as Jimmy describes. On my PC, no problems it remembers and logs on. On my laptop though, having gotten rid of cookies and other recommended "stuff", it remembers me as I...
  7. Replies
    40
    Views
    1,536

    Well said Paul!!!!!!! As I sit here getting...

    Well said Paul!!!!!!!

    As I sit here getting ready to go up to the VA docs up in Murphysboro, a 3 hour drive, thinking of how reading this surely makes me think of what used to be...........Am...
  8. Replies
    13
    Views
    494

    Easy look up: http://www.woodyswheelworks.com/

    Easy look up:

    http://www.woodyswheelworks.com/
  9. Replies
    13
    Views
    494

    Maybe someone will chime up with the folk's over...

    Maybe someone will chime up with the folk's over at Woody's.........If not....perhaps a google search will do it for you.........YOU cannot do better than them.........God bless........Dennis
  10. Replies
    10
    Views
    415

    Love that MMO, Mr. Jimmy...........One never runs...

    Love that MMO, Mr. Jimmy...........One never runs out of uses for it..........God bless.......Dennis
  11. When I finally traded in my /6 with close to 200K...

    When I finally traded in my /6 with close to 200K on it, it was dressed out with an Avon fairing, /7 seat and /7 tank.......All in black and was totally a the best BMW I ever...
  12. Replies
    10
    Views
    415

    What kind of noise?.....Where is that noise...

    What kind of noise?.....Where is that noise coming from????...................Can you put your finger on where the noise is coming from and feel anything binding or whatever?........Good luck.....God...
  13. Replies
    3
    Views
    220

    Looks like a Reynolds "ride off" to...

    Looks like a Reynolds "ride off" to me..............The wimpy part that you mention was never intended as something to use to lever the bike up onto the center stand. Unfortunately, some folks used...
  14. Replies
    28
    Views
    987

    Jammess.........Surely am glad you got all of the...

    Jammess.........Surely am glad you got all of the little problems that added up to a big one with the not properly starting issue. NOW....it would seem that perhaps with it starting so well you will...
  15. Replies
    28
    Views
    987

    [QUOTE=lkchris;955157]All gasoline engines...

    [QUOTE=lkchris;955157]All gasoline engines require two things to start cold

    Your Airhead has neither, and therefore you have to manually open the throttle a bit. You need the extra velocity...
  16. This topic has been covered MANY times in the...

    This topic has been covered MANY times in the past and a search for carb adjust or sync will show you many threads about this.

    The latest that Kurt, others and myself spent time with that...
  17. Replies
    28
    Views
    987

    Before messing with your needles, perhaps you...

    Before messing with your needles, perhaps you could try going IN 1/8" to 1/4" turn on the offending carbs air/fuel screw........for what you are describing the best and easiest thing to...
  18. So, out 2 turns.........go in and the idle...

    So, out 2 turns.........go in and the idle increases.........keep going in and you will hear it begin to fall off........NOW......back out until it runs the fastest....YOU FOUND THAT SWEET...
  19. Bud......there is nothing sacred about this 2...

    Bud......there is nothing sacred about this 2 turns business..........For me, I usually end up going in from there till the cylinder falls off, RPM drops, and then begin to back out...
  20. I really have never heard of taking temp readings...

    I really have never heard of taking temp readings to check out the mixture for a small type engine.........Can't see why it cannot be useful information. In the past, seldom heard anymore, was to...
  21. I don't know if you are refering to the class of...

    I don't know if you are refering to the class of TPM's, tire pressure monitor, or something specific. For me, I have been using Hawks Head TPM monitors for years now on my Airstream trailer, F250...
  22. Often, new springs for the advance unit does...

    Often, new springs for the advance unit does wonders; but one can easily get a whole new advance unit. Has yours been cleaned up and lubricated with proper grease? Have you got a buddy that you can...
  23. Jason........ First off you are getting some...

    Jason........

    First off you are getting some really good advice here.......Mike's thoughts and concerns are totally valid and if your compression really is as bad as indicated you will NOT get...
  24. Replies
    22
    Views
    1,313

    Welcome aboard BUD.............LOTS of work and...

    Welcome aboard BUD.............LOTS of work and love there in front of you......Glad you have a kick starter to help you get the engine turning over...........to me, that is the first thing to...
  25. The carbs are cleaned, rubber bits in good...

    The carbs are cleaned, rubber bits in good shape...........????????..............Glad you are smart enough to run cooling fans....You can't have enough so make sure you get LOTS of air...
Results 1 to 25 of 1101
Page 1 of 45 1 2 3 4