Search:

Type: Posts; User: r80andr100rt; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    10
    Views
    638

    My mistake, I thought he was asking about my...

    My mistake, I thought he was asking about my 1995 R100RT "Classic". I guess the "Last Edition" line must have been earlier models.
  2. Replies
    10
    Views
    638

    OK so you must be talking about the fairing. The...

    OK so you must be talking about the fairing. The side cover is the piece directly below your thigh while sitting on the bike. That piece, the side cover has no decal. The fairing has a decal. It...
  3. Replies
    10
    Views
    638

    They are the same from 85 to 95. Its charcoal...

    They are the same from 85 to 95. Its charcoal grey and has no lettering. Are you going to try to make one? Which side as they are different.
  4. Replies
    13
    Views
    609

    If it were mine I'd start looking for a...

    If it were mine I'd start looking for a replacement. I would never feel comfortable having repaired an aluminum rim . Its not as ductile as steel. A blowout/crash can't be worth the price of a...
  5. Replies
    13
    Views
    736

    I don't see how the late model airheads can be...

    I don't see how the late model airheads can be out of alignment by tightening the cap and stem nuts. The bottom of the fork stem aluminum bracket holes are 1.25 inches deep and a tight fit . If you...
  6. Replies
    8
    Views
    681

    I use permatex form-a-gasket on mine so I don't...

    I use permatex form-a-gasket on mine so I don't have to tighten them much to get a seal and they don't back out.
  7. Good point I hadn't thought about the valves.

    Good point I hadn't thought about the valves.
  8. Thanks Jeff I'll probably pass on this idea as I...

    Thanks Jeff I'll probably pass on this idea as I can see a lot of headaches trying to unscrew them.
  9. Will 40mm Bings mount on a 85-95 airhead?

    Thanks.
  10. Replies
    20
    Views
    1,675

    I really appreciate all the things Matt...

    I really appreciate all the things Matt publishes. Most everything he writes translates to later bikes but I wish he had a post 1984 series airhead to tinker with. Great guy.
  11. Heres the manual...

    Heres the manual
    http://i194.photobucket.com/albums/z96/lichtenau/hbkcover_zps7567d865.jpg
    http://i194.photobucket.com/albums/z96/lichtenau/300-10_zps7bd68cc4.jpg


    An engineering drawing would...
  12. Fork tube capacity. What is 300-10cc ? 290-300?

    Thanks.
  13. If the closer coils are softer I think that they...

    If the closer coils are softer I think that they should go in first. The reason is the rest of the spring would remain relatively sill in the tube as the close coils compress and expand.

    If the...
  14. Fork springs, tight coils up or down? Thanks.

    .
  15. Replies
    5
    Views
    661

    How will you get the races out and the bearing...

    How will you get the races out and the bearing off the stem?
  16. Thanks Jim. My Clymer manual said to take the...

    Thanks Jim. My Clymer manual said to take the brace off when removing the forks but I can't see why. Worse case I'll take it off if they bind up sliding out. Luckily I have a single brake which I...
  17. Fork removal brace above fender 85 R80

    Do I remove this or will the forks come out as a unit? Thanks
  18. Replies
    9
    Views
    898

    I wish I knew who made these replacements. I...

    I wish I knew who made these replacements. I bought it in Germany. Its on my RT.
    http://i194.photobucket.com/albums/z96/lichtenau/sidestand_zpsab42e27a.jpg
  19. Where to get heat sink paste for mounting ignition unit?

    Its been on there for nearly 30 years. I was thinking of rermoving cleaning area and remounting> OR.......since it works,don't touch it?
  20. Replies
    2
    Views
    253

    The little 1/4 wrench on a screwdriver bit was...

    The little 1/4 wrench on a screwdriver bit was how I got them out. Also shown is a flexible driver I put on the end of a bit type screwdriver.which made all the screw removals easier. ...
  21. Replies
    20
    Views
    988

    Its funny, In Virginia Beach I replaced the hex...

    Its funny, In Virginia Beach I replaced the hex bolts with alan head screws. Then I took the R100RT to Germany. I had it serviced while there and the dealer put back in the hex head bolts. They...
  22. Replies
    5
    Views
    749

    Heres where I put the screw in 28 years ago. ...

    Heres where I put the screw in 28 years ago.

    http://i194.photobucket.com/albums/z96/lichtenau/gascap_zps9007a2a4.jpg
  23. Replies
    9
    Views
    866

    I wish I could find another one like this I could...

    I wish I could find another one like this I could deploy while on the bike.
    http://i194.photobucket.com/albums/z96/lichtenau/sidestand2_zps5bf04511.jpg
  24. Where do you get this paste? Is there a USA...

    Where do you get this paste? Is there a USA parts store that has an equiv?
  25. Standard BMW airheads are nice to plod along on a...

    Standard BMW airheads are nice to plod along on a sunny afternoon on a country road, but I never ever got a rush out of one like I did riding my 75 Commando or 78 Triumph Bonnieville. Nice picture, ...
Results 1 to 25 of 171
Page 1 of 7 1 2 3 4