Search:

Type: Posts; User: ROBOB100S; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.05 seconds.

  1. Replies
    10
    Views
    780

    Thanks guys

    Thanks for the help, I will try turning it. Robert
  2. Replies
    10
    Views
    780

    Dips from boot

    Today I found two small tears in the drive shaft boot, on my 77ÔÇÖ R100S.
    Any tips or tricks on the r&r of the boot would be helpful. Robert
  3. Thread: Re-helicoil?

    by ROBOB100S
    Replies
    7
    Views
    951

    Re-helicoil?

    Thanks to the P.O. the ground cable nut was stripped, and repaired with a heilcoil.
    This afternoon it came out with the nut.
    Should I just redo the coil or is it one and done?
    I haven't any...
  4. Replies
    11
    Views
    1,615

    Help with pushrod seals job gone south

    Help IÔÇÖm in deep water for me, It started with changing out the pushrod seals. 77ÔÇÖ R100S 20000 miles on her and she's my baby.
    A nice intermediate job for a Saturday afternoon, my first...
  5. Thread: Drips

    by ROBOB100S
    Replies
    2
    Views
    495

    Drips

    Hi guys, hope you can help me with my 77 R100S
    I have a drip off of the clutch release arm, as been dripping all summer.
    It appears to be gear box oil, was the only low fluid all summer.
    The...
  6. Replies
    12
    Views
    933

    Thanks guys

    Thanks guys great stuff, found some nylon screws, 10 32x1 worked well, only in white.
    I will keep looking for black. Robert
  7. Replies
    12
    Views
    933

    Windscreen rivets

    Hi guys, any tips on how to install the stock rivets on an S fairing?
    I understand that they stem part should go all the way in, is there a tool that I can use? The first set I put in, came loose...
  8. Replies
    2
    Views
    439

    Add a horn kit

    Hi guys, Anyone every use the BMW kit to add a secon horn? I'm not sure now to hook it up. Came with a horn , relay, base and wireing. Hope someone has seen this before, NOS off flea- bay. From now...
  9. Replies
    16
    Views
    1,680

    Installed e-z clutch

    Hi guys, just got done installing the Bench Mark E-Z Clutch.
    Took a little over an hour, and wow, lives up to it's name!!
    Just what the doctor ordered!!
    Thanks, Robert
  10. Replies
    16
    Views
    1,680

    Help with a sore hand

    Hi guys, Anyone had experence with or heard or an E-Z clutch?
    Are they still makeing it? Is there any thing for a sore left hand.
    Old age and hard work make the clutch painful in rush hour.
    Thanks
  11. Money spent

    Just don't tell my wife!
  12. Replies
    1
    Views
    916

    Help with dyna 3 timing

    I installed a Dyna 3 ignition this afternoon as the last part of a lot of work this winter on my ÔÇÿ77 R100S.
    The carbs are out of sync, from new cables but she will run..
    The new Dyna...
  13. Replies
    2
    Views
    1,009

    Fork boot dilemma

    Guys, I love the look of fork boots, but I'm not sure if I can use they on the 77R100s? How and where can I clamp them? I know that their not stock but....
    Robert
  14. Replies
    11
    Views
    1,098

    more pads

    The other caliper
  15. Replies
    11
    Views
    1,098

    brake pads

    R&R? wron brake pads
  16. Replies
    11
    Views
    1,098

    Down to the bones

    Here she is after the tear down, Can anyone I.D. the springs by the yellow paint?
    Is there an O-ring at the bottom of the sliders that need replacing? No leaks before the disassembly. The front...
  17. Replies
    11
    Views
    1,098

    Here she is, Conela

    Cinnamon
  18. Replies
    11
    Views
    1,098

    Next step 77 R100s

    Thanks for all the help this winter work over the R100S with 17000 miles on her.
    I started at the rear wheel and moved forward, With your tips and links.

    I'm Going to install an S fairing, forks...
  19. Replies
    14
    Views
    1,148

    Oh Crap!

    I like to get my hands on the P.O.!!
  20. Replies
    14
    Views
    1,148

    exhaust size

    The inside of the pipe is 37.87mm or 38mm.
    Thanks for the help everyone! The nuts came off ok, sort of, I will clean they up and take some pixs. The right side has some, I fear may have been...
  21. Replies
    14
    Views
    1,148

    Installing a new exhaust system

    Oh wise ones, I need some advice on putting on the new headers and mufflers on a ÔÇÿ77 R100S. I know that there are tricks to the job so that it goes easier, just canÔÇÖt remember them, lol. I...
  22. Thread: Top end work

    by ROBOB100S
    Replies
    2
    Views
    1,110

    Thanks

    Thanks for the good Info, Robert
  23. Thread: Top end work

    by ROBOB100S
    Replies
    2
    Views
    1,110

    Top end work

    Hi guys
    Anyone have experience with a local shop (Portland / Vancouver) for top end work? Or I'm I better off shipping the parts off?
    Any recommendations?
    Robert
  24. Replies
    19
    Views
    1,562

    Info please

    Can anyone recommend a shop in the Vancouver WA, Portland area for the top end parts work?
    Valve seats and balancing of that pistons and pins, rods, ect.
    How about the cost? thanks
  25. Replies
    3
    Views
    1,157

    More snow today

    First real snow in years, people just freak out, but that's to be expected.
    I work for ti-met , and I work on the light rail system ( max) lots of hours at work!
    Snow snow go away! Robert
Results 1 to 25 of 60
Page 1 of 3 1 2 3