Search:

Type: Posts; User: bobr9; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    6
    Views
    317

    http://www.plastex.net There are a number of...

    http://www.plastex.net

    There are a number of adhesives that will probably work, but I have found plastex to be the best. It actually makes new plastic for the bond. I fixed my flange pieces that...
  2. Replies
    1
    Views
    212

    The mirror needs to come off. There is one screw...

    The mirror needs to come off. There is one screw underneath that needs to come out. You remove the mirror by holding it underneath with your right hand, then with tour left palm heel gently hit the...
  3. Replies
    3
    Views
    238

    Ok, I'll go out and check the screws. What is...

    Ok, I'll go out and check the screws. What is the best way to check for intake air leaks? Thanks
  4. Replies
    3
    Views
    238

    Step Change In Idle Speed

    1999 R1100RT

    I have been experiencing erratic behavior with idle speed on a warmed up engine, no fast idle lever. It seems to idle at either 1100 rpm (where I try to set it) or about 800 rpm. I...
  5. Replies
    2
    Views
    319

    O2 Sensor Connector

    1999 R1100 RT

    I have been troubleshooting a bad pin 4 connection on my O2 sensor connector. Pin 4 supplies 12V to the O2 heater. I have verified that the problem is that the male and female...
  6. Replies
    7
    Views
    707

    I think I may have a similar problem, although it...

    I think I may have a similar problem, although it still produces some effect, but the cable sheath always pops out of the handlebar lever. Is it just a matter of adjusting until you run out of...
  7. Replies
    2
    Views
    273

    O2 Sensor Resistance

    1999 R1100RT

    I am troubleshooting a problem with erratic operation and have narrowed my search to a suspect O2 sensor connector, pin 4 specifically, which supplies 12V to the O2 heater. I need to...
  8. Replies
    2
    Views
    375

    R1100RT Herky Jerky Running

    1999 R1100RT

    Bike has been running beautifully. Have gas in the tank and recently changed the fuel filter (external). About a 1/2 mile out from the house it starts running erratically, herky...
  9. Replies
    9
    Views
    280

    Thanks guys. Easy when you know how. I probably...

    Thanks guys. Easy when you know how. I probably would have pulled it and screwed it up. It came right apart.
  10. Replies
    9
    Views
    280

    O2 Sensor Connector

    Need a little help understanding how to uncouple the O2 sensor harness connector. Not sure if it just pulls apart or if it unscrews. Don't want to force it cause it is old and brittle looking. ...
  11. Replies
    287
    Views
    69,711

    Can someone confirm that to install the AF-xied...

    Can someone confirm that to install the AF-xied on a 99 r1100rt you only need to remove the right side fairing panel to do the splice into the O2 sensor wiring and not remove the gas tank? Thanks
  12. Replies
    11
    Views
    591

    Ok, so basically it sounds like a wash in the...

    Ok, so basically it sounds like a wash in the grand scheme of things. Although I have seen a lot of threads on this topic I have not paid much attention. I did not know about the LC-1 option, and I...
  13. Replies
    11
    Views
    591

    Hmmm...good point as well...so, sounds like if...

    Hmmm...good point as well...so, sounds like if you put one of these on an already good running 1100, one with little or minimally noticed surging, then you could probably expect lower mpg, while if...
  14. Replies
    11
    Views
    591

    In HW's beta test report (thanks for the link) he...

    In HW's beta test report (thanks for the link) he reports an increase in mpg. Would this be the normal expectation? I always thought richening the fuel mixture would result in lowering the mpg. I...
  15. Replies
    7
    Views
    955

    Thanks...

    Thanks...
  16. Replies
    7
    Views
    955

    Thanks GS...now my next question. I am assuming...

    Thanks GS...now my next question. I am assuming the clip is meant to be centered (front to back centered) within the caliper body. Also, I am assuming that the two tangs that stick up are meant to...
  17. Replies
    7
    Views
    955

    GS.....can you tell me which side of the clip...

    GS.....can you tell me which side of the clip faces up towards the top of the brake caliper? I can't find a decent diagram and it just fell out when I took it apart. Thanks...
  18. Replies
    2
    Views
    810

    Rear brake pad spec

    1999 r1100rt

    Anyone know if it is ok to use the EBC HH sintered pad on the rear instead of an organic pad? Some others have suggested that the original spec was for organic and you are to only...
  19. Replies
    7
    Views
    955

    Rear Brake Anti-Rattle Clip???

    99 R1100RT

    Anyone know what the little spring clip (don't know what else to call it) is that falls out when you remove the rear brake pads? I assume it is some type of anti-rattle spring/clip. ...
  20. Replies
    13
    Views
    1,128

    OK, I got it now. thanks very much. I have...

    OK, I got it now. thanks very much. I have another 16k to go assuming it passes visual inspection when I do the valve adjustment.
  21. Replies
    13
    Views
    1,128

    Ok, so now I am confused. My interpretation was...

    Ok, so now I am confused. My interpretation was that if I had the "older" setup, that the recommended change interval was 24k, while the newer setup was 36k with the "stretch belt". Is the 40k a...
  22. Replies
    13
    Views
    1,128

    Current belt has been installed for nearly 5...

    Current belt has been installed for nearly 5 years and has about 20k on it, plus it looked to be in good shape when I adjusted the valves last year. I was just trying to determine if I could go...
  23. Replies
    13
    Views
    1,128

    Alternator Belt - Which Type?

    Anyone know if the newer, "maintenance free" Poly V Belts were installed on 99 R1100RT's? (with recommended 36k change interval) My Haynes implies that they were, but not 100% sure. PO changed it...
  24. Here is a shot of my install.

    Here is a shot of my install.
  25. I am travelling now but will snap a picture when...

    I am travelling now but will snap a picture when I get back at the end of the week and post. The fuse block is the PC-8 from EasternBeaver (easternbeaver.com), although there are others. If you use...
Results 1 to 25 of 145
Page 1 of 6 1 2 3 4