Search:

Type: Posts; User: godfather; Keyword(s):

Page 1 of 22 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    14
    Views
    511

    Very nice of you Dennis! The MOA community is...

    Very nice of you Dennis! The MOA community is truly "family"
  2. Replies
    14
    Views
    511

    The first place I would start would be greasing...

    The first place I would start would be greasing the barrel end in the levers themselves. Where the cable attaches to the lever, there is a barrel that must be greased. Take a good look at the cable...
  3. Replies
    10
    Views
    439

    If the brake fluid is getting past the O Rings...

    If the brake fluid is getting past the O Rings (seals) it should collect in and drip from the rubber boot that encases the rear of the master cylinder correct?
  4. Replies
    20
    Views
    1,534

    I had the pleasure of meeting Matt at the rally....

    I had the pleasure of meeting Matt at the rally. He's very humble and quite the gentleman.
    I thanked him for his contribution to the MOA and for sharing his knowledge and expertise.

    I am not the...
  5. Replies
    6
    Views
    241

    Gorilla glue is what I used

    Gorilla glue is what I used
  6. Replies
    6
    Views
    400

    I replaced mine with a new and improved version...

    I replaced mine with a new and improved version from Max's (I believe) It has a shoulder/head that prevents it from falling out if you should somehow loose the retaining clip. Worth the few bucks...
  7. Replies
    2,749
    Views
    868,433

    Sticky: Thank you. Trying to find suitable straps. In...

    Thank you.
    Trying to find suitable straps. In the meantime, these will have to do.
  8. Replies
    2,749
    Views
    868,433

    Sticky: Wellston is my mailing address

    Thanks. Weather should be nice.
    PM sent
  9. Replies
    2,749
    Views
    868,433

    Sticky: 1978 r100/7

    After refurbishing the basic mechanicals, rebuilding the Bings, tweaking, sealing and resealing the engine, tuning, torquing, cleaning, scrubbing, detailing, adding a few accessories, test riding,...
  10. Replies
    8
    Views
    434

    Normal...time to adjust em'

    Normal...time to adjust em'
  11. Replies
    8
    Views
    657

    You can try to slide the throttle assembly...

    You can try to slide the throttle assembly towards the center of the handlebar about 1/8" putting a little pressure on the grip (stretching the rubber). Tighten the throttle in that position then...
  12. Replies
    18
    Views
    1,183

    I remember seeing a filmstrip (us old guys...

    I remember seeing a filmstrip (us old guys remember those) in HS shop class where they did a dramatization with a mannequin wearing a necktie using a drill press and again with a lathe...neither one...
  13. Replies
    29
    Views
    1,598

    Is it possible the diaphragm is bad and got worse...

    Is it possible the diaphragm is bad and got worse after the initial ride?
  14. Replies
    21
    Views
    1,821

    aside from the red....I like the paint scheme. ...

    aside from the red....I like the paint scheme.

    I see 78' R100S' w/low mileage and in VG+ condition listed for anywhere from $3800 to $6500...I do not know what they actually sell for though.
  15. Replies
    7
    Views
    520

    Be sure to sand or scuff and thuroughly clean the...

    Be sure to sand or scuff and thuroughly clean the surfaces before using the JB
  16. Replies
    7
    Views
    520

    JB Weld worked for me. Clean off all of the old...

    JB Weld worked for me.
    Clean off all of the old glue and
    scuff the surfaces. Clean with acetone and slap on the JB. It is not going anywhere...ever
  17. Replies
    11
    Views
    1,157

    update.... well, I brought the /7 home today....

    update....

    well, I brought the /7 home today. Adjusted the butterfly stop screws to get the idle at 1100 rpm then balanced the carbs enough to go get gas, and do a 20 minute warm up ride.
    When I...
  18. Some folks have had success with pine-sol or...

    Some folks have had success with pine-sol or simple green
  19. Replies
    23
    Views
    1,380

    Just when I thought we were done...2+" snow this...

    Just when I thought we were done...2+" snow this afternoon, temps in teens tonight 20's tomorrow...

    The weekend is supposed to be mid 50's with rain Sat but clear Easter Sunday. Looks like I may...
  20. Replies
    23
    Views
    1,380

    Yeah...it will be like riding through craters on...

    Yeah...it will be like riding through craters on the moon, but at least I'll be riding.
  21. Replies
    23
    Views
    1,380

    Thanks Paul, rub it in. How about you bring...

    Thanks Paul, rub it in.

    How about you bring some of that nice weather to MI...while you're here you can help me dial in my carbs.
  22. Replies
    23
    Views
    1,380

    OK...it was so nice today...I just had to try and...

    OK...it was so nice today...I just had to try and start her up

    Fuel on...
    Enricher on...
    Key on...
    Clutch lever pulled...
    Hit starter button...crank, crank, crank for four seconds..........
    ...
  23. Replies
    23
    Views
    1,380

    When will winter end?

    I, like many others, am waiting for this God forsaken extended winter to go away. It's killing me!

    The bike is done and just waiting to rotate the fuel petcocks to the on position and hit the...
  24. Thread: Back at it

    by godfather
    Replies
    6
    Views
    578

    So befitting the utilitarian BMW...I really like...

    So befitting the utilitarian BMW...I really like the look!
  25. Replies
    1
    Views
    305

    Very cool! Let us know how she goes down the...

    Very cool! Let us know how she goes down the road.

    I cannot wait to get my /7 out...this snow is never going away!
Results 1 to 25 of 531
Page 1 of 22 1 2 3 4