Search:

Type: Posts; User: roger 04 rt; Keyword(s):

Page 1 of 53 1 2 3 4

Search: Search took 0.16 seconds.

  1. Replies
    2
    Views
    180

    As Paul said your bike will run warmer at idle,...

    As Paul said your bike will run warmer at idle, and it will use more fuel.

    With your Techlusion installed this next comment may be a moot point but your bike will run lean during a cold start....
  2. The o-ring that seals the gas cap to the tank...

    The o-ring that seals the gas cap to the tank expands. Be sure that it was in its grove or you could have an unintended opening where the gasket didn't seat. When I took delivery of my bike years...
  3. True but he's gotten a good result without...

    True but he's gotten a good result without re-alignment.
  4. So it seems to me that Anton Largiader's view...

    So it seems to me that Anton Largiader's view that clutch pack damage/distortion is more of a factor than transmission-engine alignment is right.

    It will also be interesting to see what else...
  5. Here is some more info in case you want to...

    Here is some more info in case you want to measure the sensor: http://www.uploadarchief.net/files/download/bosch%20sensors_temperature.pdf

    Here is a cross reference to Bosch:...
  6. Two wires: violet and black/yellow. PN...

    Two wires: violet and black/yellow.

    PN 12611341602 I believe.

    http://www.beemerboneyard.com/11411342761.html $30 at Beemerboneyard.

    It is located on the block below the O2 sensor connector....
  7. +1, thanks for following this up. Did you replace...

    +1, thanks for following this up. Did you replace some of the clutch parts and input shaft, or all as Anton had recommended?
    RB
  8. Replies
    291
    Views
    74,951

    The Free-Air calibration did not completely...

    The Free-Air calibration did not completely restore my LC-1 to perfect operation after my +12V tap failed. After some internet searching I found a more comprehensive procedure that worked. Below is...
  9. Replies
    291
    Views
    74,951

    Hi Lorne, My LC-1 is working but the analog...

    Hi Lorne, My LC-1 is working but the analog output is not molding the "high" voltage perfectly. The AFR log to logworks is fine and the Motronic doesn't care about the high voltage but I so. My next...
  10. Replies
    12
    Views
    545

    A couple thoughts-- I would have your mechanic...

    A couple thoughts--

    I would have your mechanic try one of the "bad" modules in another bike and also find someone to carefully check ground,

    The HID/LED module would have to be outputting a...
  11. Replies
    291
    Views
    74,951

    I ran into an interesting problem with my...

    I ran into an interesting problem with my Innovate Motorsports LC-1. My +12 volt lead, which is tapped from the lambda sensor heater became intermittent because I used a cheap fork-style tap. I fixed...
  12. Replies
    12
    Views
    545

    +1, DY is pointing you in the right direction. If...

    +1, DY is pointing you in the right direction. If I were making a wager, I'd guess that none of your RIDs failed. Let me explain why.

    Since you've said they "freeze" but have a display, it is...
  13. With the recent measurements above, I've...

    With the recent measurements above, I've concluded that the MA 2.2 and MA 2.4 behave the same. Each has a nominal setting of 340-350 mV for center of the 0.32 degree range, meaning that the expected...
  14. Comment on Earlier Posts In the earlier posts in...

    Comment on Earlier Posts
    In the earlier posts in this thread there are mistakes or omissions that I have found. The biggest error is the conventional understanding of what rotating the throttle does...
  15. Replies
    13
    Views
    557

    I found the same thing, given that BMW only...

    I found the same thing, given that BMW only replaces the male-connector, my guess is that someone damages it during insertion and removal.

    One thing I found, the female metal QD doesn't have a...
  16. Thread: EFI MODs

    by roger 04 rt
    Replies
    53
    Views
    7,650

    Hi RSH, Thanks for the report and feedback. The...

    Hi RSH,
    Thanks for the report and feedback. The description of how your bike is running is much like my experience with the LC-1 on the 1150RT. I'm usually running 5th gear now around town (35-50...
  17. Replies
    5
    Views
    688

    Your lights lit brightly, but the starter brought...

    Your lights lit brightly, but the starter brought the battery to its knees. Then everything worked. It happened to me too.

    It seems most likely to me that he has a problem with the starter. There...
  18. It doesn't sound like fuel since it has been a...

    It doesn't sound like fuel since it has been a while. Stop in at the GS-911 booth and ask them to put their new 911 wifi on your bike and see if it has produced any error codes. Maybe they would look...
  19. Thanks guys. As I mentioned, this is a work in...

    Thanks guys. As I mentioned, this is a work in progress and I expect some tweaks to the procedure.

    I think the most important point is that when the throttle is fully closed, the TPS should read...
  20. Replies
    291
    Views
    74,951

    I've had a Beemer Boneyard version of the EJK on...

    I've had a Beemer Boneyard version of the EJK on my workbench for several months, planning to check it out. I've been curious about what it does with the O2 sensor and finally got to it this week.
    ...
  21. Critique of Zero=Zero As I mentioned at the...

    Critique of Zero=Zero

    As I mentioned at the start of the thread, I'm not a fan of adjusting the TB Idle Stop screws but if you're considering zero=zero, or if someone has previously run zero=zero...
  22. TPS Alignment, Idle Speed Adjustment: Beyond Zero=Zero

    Although I'm not a fan of adjusting the throttle stop screws or TPS, since they're factory calibrated (mine are untouched and are in spec). Many motorcycles have already been altered using the...
  23. Replies
    33
    Views
    1,384

    Idle balance is pretty sensitive. You could try...

    Idle balance is pretty sensitive. You could try marking them but it would be better to buy a Twinmax or build a manometer with tubing and ATF (search and you'll find many descriptions).
  24. Replies
    9
    Views
    506

    http://www.beemerboneyard.com ...

    http://www.beemerboneyard.com

    http://www.maxbmwmotorcycles.com/fiche/PartsFiche.aspx

    http://www.euromotoelectrics.com
  25. Replies
    30
    Views
    4,359

    If your highway mileage at 75 was normally 47-48...

    If your highway mileage at 75 was normally 47-48 mpg, and you set 12.8:1 which is about 13% richer than stock, I'd expect a 7-8% drop in fuel mileage at that speed. That would calculate to about 4...
Results 1 to 25 of 1320
Page 1 of 53 1 2 3 4