Search:

Type: Posts; User: JamesInCA; Keyword(s):

Page 1 of 14 1 2 3 4

Search: Search took 0.06 seconds.

  1. That's a great list, rcxrider. Can you...

    That's a great list, rcxrider.

    Can you elaborate on "noise at a stop in neutral with clutch engaged and disengaged"? What's this?
  2. Replies
    3
    Views
    150

    On a side note, for future readers of this...

    On a side note, for future readers of this thread, the R1100 50A alternator is the same part as the K75 50A alternator, but with about $20 of different parts on the front. For whatever reason, the...
  3. Replies
    9
    Views
    496

    I used to have a big showerhead with about a...

    I used to have a big showerhead with about a hundred of those screwed into the face. So I'm guessing "showerhead micro-nozzle," or whatever such a part would be called.
  4. Just a note on the paralever bearings in...

    Just a note on the paralever bearings in particular: I wouldn't consider this a reason not to buy an otherwise appealing bike.

    I think of them now like, say, a clutch plate: You'll probably have...
  5. Replies
    34
    Views
    1,632

    How would a defective fuel-level sensor cause you...

    How would a defective fuel-level sensor cause you to run out of fuel?
  6. Thread: unknown BMW

    by JamesInCA
    Replies
    6
    Views
    969

    You are just asking for a big bag of hurt. Let...

    You are just asking for a big bag of hurt. Let him be frustrated with someone else.
  7. Thread: Do I really?

    by JamesInCA
    Replies
    31
    Views
    1,568

    For me: Oil: Mobil1 15w50, $25/5qt at WalMart...

    For me:

    Oil: Mobil1 15w50, $25/5qt at WalMart
    Filter: Bosch D3331, $12 at WalMart
    Plugs: Autolite 3923, $3/pair at WalMart
  8. Replies
    1
    Views
    162

    Will your son fit in 50L?

    Will your son fit in 50L?
  9. If the speed bleeders have been in there for a...

    If the speed bleeders have been in there for a while you may just need new thread sealant:

    http://www.speedbleeder.com/install.htm
  10. That's where I jammed a piece of 2x4 into the...

    That's where I jammed a piece of 2x4 into the corner of the case. That plus engine compression was just enough to hold the flywheel to get the required torque on the clutch bolts, which isn't...
  11. IIRC, the TDC mandrel is only usable when the...

    IIRC, the TDC mandrel is only usable when the transmission is in place, as it uses the hole through the transmission housing as the stop.

    The tool BMW specifies for locking the flywheel in place...
  12. Cable clutch (2000 R1100RT) I don't know if...

    Cable clutch (2000 R1100RT)

    I don't know if it's still grabbier; it's just the way it is for me now. :) The friction zone is adequate; it seemed a bit on the small side before anyway.

    Yes,...
  13. I replaced everything, yes. My pressure plate and...

    I replaced everything, yes. My pressure plate and housing showed distinctly tapered wear.

    9k on the new clutch since January and all is well.
  14. From the FAQ: ...

    From the FAQ:



    http://www.toptiergas.com/faqs.html
  15. Replies
    21
    Views
    1,240

    They're currently relying on luck, so this is an...

    They're currently relying on luck, so this is an improvement in my book.


    Probably already underway.

    Some cars now -- seems to be all or mostly Lexuses -- have a nifty light in the mirror...
  16. You are absolutely certain there's continuity...

    You are absolutely certain there's continuity between the ground wire in the tank, and the ground wire on the connector that emerges from the bottom of the tank and plugs into the bike harness?...
  17. Replies
    6
    Views
    383

    Redlands CA? You could call up A&M Cycle Traders...

    Redlands CA? You could call up A&M Cycle Traders in the San Fernando Valley. BMW dismantlers, nice guys.
  18. Replies
    6
    Views
    490

    Welcome to the fatherland. Sounds normal. Here...

    Welcome to the fatherland. Sounds normal.

    Here are a couple of threads with tips on shifting technique; much of this appears to be more or less applicable across different gearbox models:...
  19. Thread: 2014 rtw

    by JamesInCA
    Replies
    2
    Views
    692

    I'd say it's virtually certain they already are.

    I'd say it's virtually certain they already are.
  20. Replies
    17
    Views
    1,031

    In the first 6,000 miles, I honestly can't say I...

    In the first 6,000 miles, I honestly can't say I notice much difference between the PR3s and the BT-023s (which cost 25% less).

    Some have made the case to me that the PR3s will maintain their...
  21. Replies
    17
    Views
    1,031

    I was very happy with a set of Bridgestone BT-023...

    I was very happy with a set of Bridgestone BT-023 (since replaced by the T30) on my 2000 R1100RT. Replaced them at about 12,000 miles. They probably had another 1,000-2,000 miles in them if I'd...
  22. Replies
    10
    Views
    771

    You can also use the "Insert Image" button on the...

    You can also use the "Insert Image" button on the editor, as I've done to insert the screenshot below.

    45505
  23. Replies
    8
    Views
    738

    I had one (R1100RT) that was failing in the...

    I had one (R1100RT) that was failing in the opposite of the usual manner. It would, increasingly often, indicate neutral in both first gear and neutral. Replaced it during the holiday spline lube and...
  24. Will do as a first step prior to tearing in, but...

    Will do as a first step prior to tearing in, but I'll note it was so adjusted (5mm rather than 7mm; still within spec) on January 18. To have the level of adjustment creep necessary to render the...
  25. Two days and nothin'? Not even a suggestion that...

    Two days and nothin'? Not even a suggestion that I check the clutch piston, AKA throwout bearing?

    Well, JamesInCA, since you mentioned it: Might one somehow be able to distinguish a bad clutch...
Results 1 to 25 of 327
Page 1 of 14 1 2 3 4