Search:

Type: Posts; User: ratze; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.05 seconds.

  1. Speaking of which, i need a good source on the...

    Speaking of which, i need a good source on the E10 or the E15 cure all. my bike runs so much better when i use it, i ride all winter and sometimes the fuel is really bad. thanks folks.
  2. Thread: 2014 1200gs

    by ratze
    Replies
    8
    Views
    698

    140 is to much for the finale drive big bearing,...

    140 is to much for the finale drive big bearing, i run 70/90 with the guzzi moly additive. quarter million miles, i do use 140 in gearbox. just my preference. but what do i know,,,
  3. Replies
    17
    Views
    907

    the pr4 gt got me 12.5k, excellent set of tires....

    the pr4 gt got me 12.5k, excellent set of tires. i really could have pushed them another 3k but needed a more aggressive set for the haul road. handling was superb as well. metzlers are a bit rough...
  4. Replies
    26
    Views
    2,612

    Great thread, i to have had my share of slaves. i...

    Great thread, i to have had my share of slaves. i just recently replaced one on a c model simply because when i pulled the clutch back i had a knocking noise, i knew right away what it was as ive...
  5. Replies
    70
    Views
    3,390

    The big bearing is the same on c and rt, my rt...

    The big bearing is the same on c and rt, my rt has been that sloppy for 25k. the pivot bearings wer renewed last winter, still when checking 9 and 3 o clock or 12 and 6 there is a good 15 thousand...
  6. Replies
    10
    Views
    683

    All the places you have been, all mine are posted...

    All the places you have been, all mine are posted up on the aft end of the bike. states, countries ect. ill post a pic eventually.
  7. Replies
    10
    Views
    683

    Thank you, ill try er again. shoot, it keeps...

    Thank you, ill try er again. shoot, it keeps saying file upload failed. i have posted pic before. heck i dono.
  8. Replies
    70
    Views
    3,390

    OK guys, back to the basics. 02RT1150, bike on...

    OK guys, back to the basics. 02RT1150, bike on center stand. 6 and 12 oclock, 3 and 9. how much is to much, if i had to guess i have a good 16th of an inch of slack. both ways, sometimes i can feel...
  9. Replies
    10
    Views
    683

    lets see your stripes

    Maybe the wrong spot ta start this but ill start,,,cant post pics,,,WTF
  10. Replies
    5
    Views
    679

    My fuel pump blew that fuse a bunch of times...

    My fuel pump blew that fuse a bunch of times before pump failed, just a thought if its a consistent problem.
  11. Replies
    5
    Views
    526

    Lightly sand em with sanding sponge and use VHT...

    Lightly sand em with sanding sponge and use VHT flame proof header paint, comes in a rattle can at just about any auto parts. read application, 2 ways you can do it. on or off the bike. that simple,...
  12. you could not give me a new k bike,,,,

    you could not give me a new k bike,,,,
  13. Replies
    70
    Views
    3,390

    Its not that difficult of a job, i actually did...

    Its not that difficult of a job, i actually did it while on the road. had bearing an seal with, fortunately it went down close to a buddies garage in gillett wyoming. his wife did not like the idea...
  14. Replies
    18
    Views
    2,045

    Do a leakdown test or compresion check, i had a...

    Do a leakdown test or compresion check, i had a couple of guzzis with same symtoms. one weak cylinder will do it.
  15. Replies
    14
    Views
    1,325

    + 1 pas, i did both. i think i used a 1/4 inch...

    + 1 pas, i did both. i think i used a 1/4 inch bit. cant remember.
  16. When I installed mine I mixed moly with some ole...

    When I installed mine I mixed moly with some ole faishaned axel grease about 60/40. the 60 being grease. torked the right side to specs then torked the left pin to 20ft lbs then the lock nut to spec....
  17. Replies
    69
    Views
    13,621

    We took off march 1st and toured mexico, allready...

    We took off march 1st and toured mexico, allready looking past it and preparing for the hual road. cooldfoot and deadhorse alaska, I thank the lord every day for keeping me in good health to follow...
  18. Sticky: WOW, your a lucky man. i personally would be...

    WOW, your a lucky man. i personally would be honered to restore such a time piece. sparing no expence of course.
  19. Replies
    14
    Views
    1,325

    Pic,,

    Pic,,
  20. Replies
    14
    Views
    1,325

    Good day, i allways drill a weep hole into the...

    Good day, i allways drill a weep hole into the bottom of slave to aleart of impending leaks. i got that tip from anton, and believe me it works. also for the corrosion on the slave bolt, i have a...
  21. Whatever happened to the ole fashioned soda...

    Whatever happened to the ole fashioned soda blast, boy i am getten old. or maybe i just dont know what ultrasonic means,,,:doh
  22. Replies
    3
    Views
    395

    All of todays production bikes need some sort of...

    All of todays production bikes need some sort of fuel managment setup, they are starving for fuel. government regs, when i got my 2013 gs home last year i pulled the plugs ta have a peek. snow white,...
  23. Thread: R1150rt Oil Leak

    by ratze
    Replies
    10
    Views
    647

    Thats my vote to, ive changed about 3 or 4 of the...

    Thats my vote to, ive changed about 3 or 4 of the sencors out on the ole guzzi. cant remember if they wer magnetti or bosch but never the less they wer leaky. the reason i mention airbox plug is that...
  24. Thread: R1150rt Oil Leak

    by ratze
    Replies
    10
    Views
    647

    Airbox plug,,,

    Airbox plug,,,
  25. Replies
    3
    Views
    384

    Thanks rodge, your posts allways gets me a lil...

    Thanks rodge, your posts allways gets me a lil closer to the majical tune. keep em comen,,
Results 1 to 25 of 160
Page 1 of 7 1 2 3 4