HEXHEAD Tech - R1200XX - Oil Change - All Years

[SIZE="3"][B][COLOR="Red"]The articles, posts and comments in this tech section are posted by individual members and reflect their personal thoughts and experiences with repairing, maintaining, and generally working on motorcycles. This information may require specific knowledge and skills, may or may not be correct or current to model.

The authors of information found here and the BMW MOA take no responsibility for ensuring the accuracy of any information (including procedures, techniques, parts numbers, torque values, tool usage, etc.), or further for any damage of any kind or injuries incurred or caused by anyone following the instructions or information found here.

It is the duty of the individual to either assume the liability himself for responsibly using the information found here, or to take the bike or accessory to a Dealer or other qualified professional service.[/COLOR][/B]

[COLOR="Green"][B]Lastly, please ensure you dispose of your used chemicals, oils and fuels in an environmentally responsible manner. Most Auto Parts stores and service stations will accept used oil and lubricants, tires and batteries, please check for your local availability.[/B][/COLOR][/SIZE]

[B]NOTE 1[/B] – This procedure will generate approximately 4 liters (quarts) of waste oil and filter.


This article, text and photos are Copyright of the individual authors and the BMW MOA, any copying or redistributing is permitted only by prior written authorization.


Specifics:
- Bike shown is a 2008 R1200RT
- Heated Seat Option
- No Factory Radio

[B]Note 2 [/B]- even though DIY is shown for the RT it is applicable to all Hex Heads.

[B]Note 3[/B] - the tools and materials used are by personal choice and not due to affiliation with any brand

[B]Tools and materials[/B]

4 quarts oil - BMW Oil 20W50 BMW Part Number - [COLOR="Blue"]81229407685[/COLOR]

Oil Filter - BMW Part Number - [COLOR="blue"]11427673541[/COLOR]

Washer for drain plug - BMW Part Number - [COLOR="blue"]07119963252[/COLOR]

3/8” Drive ratchet and extension

8mm Hex Socket

BMW specific oil filter wrench
- I got this wrench from Max BMW in New Hampshire - [url]www.maxbmwmotorcycles.com[/url]

17mm combination wrench – for use with Filter wrench

Warm up the bike - get engine to normal operating temperature.

Put bike on Center Stand - should be a smooth and level surface

Location of Filter and Drain Plug - the view is looking up to the bottom of the engine on the clutch side. The highlighted spot on the picture is the drain plug

[COLOR="Red"][SIZE="3"][B]CAUTION - Oil will be hot if you warmed up the bike[/B][/SIZE][/COLOR]

Place a suitable oil draining container below the location of the drain plug and using an 8mm Hex remove the drain plug

[COLOR="Red"][SIZE="3"][B]CAUTION - Oil will be hot if you warmed up the bike[/B][/SIZE][/COLOR]

Now remove the oil filter using the special oil filter wrench

After oil has finished draining from the oil filter area - wipe it clean and ensure there is no residue or debris left behind,
especially on the mating surface of the filter gasket and engine block.

The next step is personal preference.

I like to fill up the new oil filter with oil before replacing.

[U]A must do,[/U] however, is applying a small amount of new, clean oil onto the filter gasket so that it tightens up well and
removes easily at the next replacement interval.

Carefully thread in filter until proper engagement is made and then torque to [B]11Nm[/B]

Once the filter is in you can replace the washer on the drain plug.

Please note that sometimes the washer gets stuck on the plug - the easiest thing to do is just snip it off

Insert drain plug with new crush washer and hand tighten to ensure proper thread engagement – once seated you can finish the tightening to torque of 32 NM

[B]Filling up the oil[/B]

Now that the oil has been drained, the filter replaced, and the drain plug reinserted you can fill up the engine with new oil.

Use this wrench to open the oil fill port found on the clutch side Valve Cover.

The wrench is a part of the supplied BMW Tool Kit

Here is where the oil fill is located on the bike.

Mate the wrench to the oil fill cover and unscrew to open.

Now fill with your favorite oil

Once you have filled the engine with the required amount of oil, close the oil fill port and tighten hand tight.

Start engine and check for leaks.

[B][COLOR="Green"]RECYCLE NOTE[/COLOR][/B]: for proper disposal of waste fluid please refer to this link to find approved recycling centers in your area [url]http://earth911.com/[/url] - special thanks to Ted for providing the link.

[B]Oil Change DIY COMPLETE[/B]

Go Ride :dance